HomeMy WebLinkAboutSFRA2019-2969- FA
STANDARD ECO
110 E. Houston St., CONTRACTOR SHALL CALL FOR
San Antonio, TX 78205 INSPECTIONS:
TX License #:32439 (817) 410-3010
VICINITY MAP
1�
f2600 Pool Road
SYSTEM INFORMATION
CONTRACTOR REGISTRATIC N ARIEL MAP
WILL BE REVOKED UPON
PERMIT EXPIRATION.
SCOPE OF WORK:
INTALL (36) ROOF MOUNTED PV SOLAR MODULES, (36) P320
POWER OPTIMIZERS,(1) SOLAREDGE 1000OH-US INVERTER
(240V), (1) 60A AC DISCONNECT, AND DERATE MAIN BREAKER TO
175A FROM 200A.
IBrittain Residence
2600 Pool Road Grapevine, TX 76051
JUL 19 2019 f a400 ra6l�.
ALL CHANGES REQUIRE
APPROVAL
OF REVISED PLANS
APPROVED s, ` n�; w e L BE.
KEPT ON JOBSITEATALL nMES
MO.`
N0
~1 h 0, 72
MY AM9M P'LANI TO BE KEPI ON
TM M SITE AT ALL TVAM
DATE: t 1 x BY:
BURDM INSPECTION .
RELEASE OM NOT APPLY TO N IN
EASEMENTS OR PUBLIC RIGHT-OF-WAY.
ALL CHANGES MUST BE APPROVED
SHEET INDEX.
-00- COVER SHEET AND PLOT MAP
-1- SITE PLAN DRAWING
-2- RACKING PLAN
-3- ELECTRICAL NOTES
-4- SINGLE LINE DIAGRAM
-5 ARRAY MAP SEPARATE PLUMBING, MECHANICAL,
-5.1- THREE LINE DIAGRAM EL.ECTRICAL.AND SIGN PERMITS
-6- PLACARDS SHALL BE REQUIRED
- - REFERENCE PAGE
- ATTACHED SPEC. SHEETS / ETC. -
-- INVERTER SPECIFICATIONS
-- MODULE SPECIFICATIONS
GENERAL NOTES
1. ALL CONSTRUCTION / INSTALLATION SHALL COMPLY WITH:
2017 NATIONAL ELECTRIC CODE (NEC)
2012 INTERNATIONAL FIRE CODE (IFC)
2012 INTERNATIONAL BUILDING CODE
2012 INTERNATIONAL RESIDENTIAL CODE
2012 INTERNATIONAL MECHANICAL CODE
2012 INTERNATIONAL PLUMBING CODE
2012 INTERNATIONAL EXISTING BUILDING CODE
2012 INTERNATIONAL FUEL GAS CODE
2012 INTERNATIONAL ENERGY CONSERVATION CODE
2. ALL DIMENSIONS WITHIN THESE PLANS ARE APPROXIMATE.
3. ALL CONDUITS ON ROOF SHALL BE A MINIMUM OF 1/2" OFF ROOF.
4. CONSTRUCTION LIMITS: ALL IMPROVEMENTS AND ACCESS SHALL
OCCUR WITHIN PLANT PROPERTY LINES.
5. PV EQUIPMENT SHALL BE INSTALLED IN ACCORDANCE WITH 2O17
NEC 690 & POSTED WITH APPLICABLE WARNINGS, SIGNAGE AND
PLAQUES PER 2017 NEC ARTICLE 705-10, 690-17, 690-64, AND 2012 IFC
SECTION 605.11.
6. ALL PV ARRAYS AND ASSOCIATED EQUIPMENT, CONDUIT AND
CONDUCTORS SHALL COMPLY WITH SECTION 605.11 OF THE 2012 IFC
FOR MARKING DC CONDUCTORS, LOCATION OF DC CONDUCTORS,
ROOF ACCESS, PATHWAYS AND SPACING. PLAN SHOULD SHOW
COMPLIANCE WITH THE IFC.
SYSTEM EQUIPMENT
(36x) MISSION SOLAR ENERGY MSE3IOSQ8T
(36x) POWER OPTIMIZERS P320
(Ix) SOLAREDGE SE 10000IWNTRACTOR COPY.
11.16 kW DC ISSUE., DRAWN BY: 00
10.00 kW AC 1 06/28/2019 1 ND
SITE PLAN
TYP ROOF ACCESS POINT
Y FIRE ACCESS PATHWAY
PROPOSED FLUSH MOUNTED SOLAR
MODULES AND POWER OPTIMIZERS
UTILITY METER
(OUTSIDE WALL)
NEW VISIBLE LOCKABLE UTILITY AC
DISCONNECT (CAPABLE OF BEING
LOCKED IN "OFF" POSITION)
IN
SCALE: 1" = 50'-0"
ELECTRICAL EQUIPMENT DETAIL
EXISTING
SERVICE PANEL _
(LOCATED
INSIDE)
D�Ewp,Y
\\K ------ ------ - — - ---------
EXISTING 200A PANEL
WITH A NEW 175A MAIN BREAKER
(INSIDE)
INVERTER MOUNTED
ON OUTSIDE WALL
UTILITY METER
CONSTRUCTION NOTES
O
1. SOLAR PHOTOVOLTAIC SYSTEM TO BE INSTALLED ON
RESIDENTIAL STRUCTURE.
W
O
2. THIS PROJECT HAS BEEN DESIGNED IN COMPLIANCE
4 N M
00
WITH THE CBC SECTION 1609 TO WITHSTAND A BASIC
N
WIND SPEED OF 110 MPH (3 SECOND GUST), WIND
M
EXPOSURE C.
3. THE HOUSE IS A ONE STORY STRUCTURE.
O U
4. THE ROOF MEMBERS ARE 2x4 RAFTERS ON 24"
W a
b
CENTERS. CONNECTION TO STRUCTURE SHALL NOT BE
WITHIN 6" OF NAILING PLATES.
O Q
po
_
5. THE SOLAR PHOTOVOLTAIC INSTALLATION SHALL NOT
O
OBSTRUCT ANY PLUMBING, MECHANICAL OR BUILDING
Q-
ROOF VENTS.
r^
6. ALL CONDUCTORS AND CONDUITS MOUNTED ON ROOF
SHALL BE MINIMUM 3 314" ABOVE ROOF SURFACE
(INCLUDING CABLES UNDERNEATH MODULES AND
RACKING).
COMPOSITION SHINGLE 7. ROOF ACCESS POINTS SHALL BE PROVIDED PER THE
ROOF STRUCTURE FOLLOWING (CRC R324.7.1, CBC 3111.4.1):
- LOCATED IN AREAS NOT REQUIRING PLACEMENT OF
GROUND LADDERS OVER OPENINGS SUCH AS DOORS
OR WINDOWS.
- LOCATED AT STRONG POINTS OF BUILDING
CONSTRUCTION IN LOCATIONS WHERE ACCESS POINT
DOES NOT CONFLICT WITH OVERHEAD OBSTRUCTIONS
SUCH AS: TREE LIMBS, WIRES, OR SIGNS
VISIBLE LOCKABLE UTILITY
AC DISCONNECT (CAPABLE
i OF BEING LOCKED IN "OFF"
POSITION)
NEW
Q � I1vV ��_SOLAREDGE
INVERTER
° (OUTSIDE WALL)
CITY OF GRAPEVINE
RELEASED FOR CONSTRUCTION
SHEET: _ 4'Z OF:
ES N
RELEASE .]DOT AUTHORIZE ANY WORK IN
OONFLICT WITH i HE BUILDING CODE OR ZONING OPMNANCE.
CITY APPF OVED PLANS TO BE KEPT ON
THE JOB SITE AT ALL TIMES
DATE: Z 2+ 20 BY:
BU LDING INSPECTION OMSION:
RELEASE DC IES NOT APPLY TO CONSTRUCTION
EASEMENTS OR PUBLIC RIGHT -OF --WAY.
ALL CHANGES MUST BE APPR[�v ,
* */ .... . ....... ......
J R. VI Cl i
. .12ES i,� 8 7 ...:...
t O l !��Oi
ZONAL
t6-28-2019
A
IIRUCTURALONLY
cslrucfural �in9ineers
Vincise.com
TSPC Finn Reg,.treL"n No F.206N
o
�l
U U N
~
N
O4
5
O V1
p _ W
PLO
CIO
REVISIONS:
DRAWN BY: ND
DATE: 06/28/2019
SITE PLAN
DRAWING
SHEET: 1
ENLARGED P.A RTT 4L ROOF/RACKING PLAN
9 I
i
6'-0"
33'-2"
, X
i • i
MISSION SOLAR
ENERGY MODULES
TYPICAL ATTACHMENT POINT W/ 5/16" S.S. LAG TO BE
CENTERED IN STRUCTURAL MEMBER. LAGS MUST
HAVE A MINIMUM OF 2.5" THREAD DEPTH INTO
STRUCTURAL BEAM
N
1800 SCALE: 1/8" = V-0"
RA CKING DETAIL
IRONRIDGE GROUNDING
MIDCLAMP
SUPPORT RAIL SPLICE AS REQ.
11'-0"
9'-11" r } -----r
I �
PV
MODULE
IRONRIDGE XR100
RAILING
L-FOOT
TYP. ATTACHMENT POINT
"QUICK MOUNT PV" SYST.
W/ 5/16" x 6" S.S. LAG. WITH
2 1/2" THREAD EMBEDMENT
INTO FRAME MEMBERS
Y FIRE ACCESS PATHWAY
2" x 4" RAFTERS CENTERLINE
16'-6"
INSTALLATION NOTES
O
1. DISTANCE BETWEEN PENETRATIONS NOT TO
u
EXCEED 6-0"
rT�
tn
w
p a,
2. RAIL OVERHANG FROM PENETRATIONS NOT TO
0"o
EXCEED 24"
m
3. LAG SCREWS SHALL BE AT LEAST 6" FROM ANY
o o
NAILING PLATES.
y
n�
4. LAGS MUST HAVE A MINIMUM OF 2.5" THREAD
p �
DEPTH INTO STRUCTURAL BEAM.
5. ADJUSTMENTS MAY BE REQUIRED DUE TO
r
EXISTING ROOF CONDITIONS.
v 1
6. THE COMBINATION OF MOUNTING SYSTEM AND
PV MODULES SHALL MEET THE MINIMUM
REQUIREMENTS TO ACHIEVE A CLASS "A" FIRE
RATING PER UL 1703 FIRE CLASSIFICATION
U
o
STANDARDS.
W
N
U U
7. PV EQUIPMENT SHALL BE INSTALLED IN
a 00
Q N
r,
ACCORDANCE WITH THE 2017 NATIONAL
ELECTRICAL CODE ARTICLE 690.
CONSTRUCTION MUST ADHERE FOR BOTH
Q
O
INSTALLATION OF ELECTRICAL WIRING AND
EQUIPMENT ASSOCIATED WITH THE SOLAR
C
PHOTOVOLTAIC SYSTEMS.
a
CITY 9F GRAPEVINE
RELEASED FOR CONSTRUCTION
SHEET: OF: 5 PtE .r ''
r
RELEASE DOES N T AUTHORIZE ANY WORK I(* ,3
CONFLICT WITH THE BUILDING CODE ORZ NIN ES R. VI ci
4
CITY APPROVED PLANS TO BE KEPT 1427
THE JOB ITE AT ALL TIMES �� ��ONAI.rr
6-28-2019
DATE: 2I� BY: R CTURAL ONLY
BUILDING INSPECTION DIVA ION:
RELEASE DOES NOI APPLY TO CONSTRUCTION IN
EASEMENTS OR PUBLIC RIGHT-OF-WAY.
ALL CHANGES MUST BE APPROVED
cSfrucfural �inyineers
vincise.com
TBPE Firm Regmi,alion No, F-20604
REVISIONS:
DRAWN BY: ND
DATE: 06/28/2019
RACKING PLAN
SHEET: 2
r0
PHOTOVOLTAIC TABLE MAXIMUM SYSTEM VOLTAGE V
BRITTAIN RESIDENCE OPERATING VOLTAGE FOR DC PV SOURCE CIRCUITS W o Q,
MISSION SOLAR ENERGY MODULE hfSE310SQ8T Zip Cade &05t (PER NEC 690.7 110.3(f3) WITH SUPPLIED MANUFACTURER'S TEMP COEFFICIENTS) 0 N
PEAK POWER IP aJc ETC] 310 �gverage High! 96-F f 36-C j
RATED VOLTAGEri Irt�p) �3,j7 tZecard LowI -S'F I -22°C 40.12 V MODULE V(iC
RATED CURRENT mp ids Exposed Conduit Yes 12 MODULES IN DC LARGEST SERIES p o m
OPEN CIRCUIT VOLTAGE (yoc) 40.12 -0 2800 MODULE TEMP COEFFICIENT (V) x o v
SHORT CIRCUIT CURRENT i1scl 9J16 Grapevine TX
NUMBER OF SOLAR CELLS EO 12 x lap.12(VOC I.11+(-23' - 25-F (sTC1) x -02s r1 OO I = 545.10 VDC {MAXIMUM SYSTEM VOLTAGE)MODULE TEMPERATURE COEFFICIENT iVOQ -0.29W a
p
PHYSICAL SIZE 65.51h x 39.33W x 1.57d & 40.116s 12 x 33.17(VMP)= 398.04 VDC (OPERATING VOLTAGE) 1�-1
BRITTAIN RESIDENCE DEAD LOAD
Module MSE310SQBT CONDUCTORYAMPACITY W
PV SOURCE CIRCUITS (DC) N U U
'Weight 40.1 lbs [� o
9.76 MODULE ISC (A). i"i Q N
Area (Module) 17.9 sq_ ft. a r/1
15.23 MINIMUM DC AMPACITY (A)
126 OF DESIGN TEMP (INCLUDES ROOF TOP ADJ. FACTOR)
Q
Quantity Lbs. t Unit Lbs. 1 Qty. 1.12 DESIGN TEMP ADJUSTMENT FACTOR 0
Module 36 40.1 1444 0.80 CONDUIT FILL FACTOR �
Power Optimizer 36 1.0 36 Q >0
Midclamp 60 0.1 3 12.20 STRING#SC fA) = 13.62 A x
Endclamp 24 0.1 1.4 1 12 (DESIGN TEMP FACTOR) x 0.8 (FILL FACTOR) CIO
L-Foot 54 0.2 12 CONDUCTOR AMPACITY
Rail 240 0.8 195
AC CIRCUITS
Tilt Leg 0 1.5 0 r
Splice bars 1 17 1 0.5 9 42 MAX INVERTER OUTPUT (Al (EACH)
Footings 54 2.2 121 52.5 MINIMUM AC AMPACITY (A) �
96 OF DESIGN TEMP
Total 'WeightIArray 1820 Lbs 1.12 DESIGN TEMP ADJUSTMENT FACTOR v �
Total Area ) Array 644 Sq.ft- 0.80 CONDUIT FILL FACTOR
Lbs. per SQFT 2.8 Lbsisq.ft.
Lbs. per Standoff 33.7 Lbs 42.0 MAX AC OUTPUT (A) (TOTAL)
= 46.88 A � U
1.12 DESIGN TEMP FACTOR) x 0.8 (FILL FACTOR) y as
CITY OF GRAPEVINE p�G,
RELEASED FOR CONSTRUCTION o
SHEET: OF: P� .. • �..•'r o
RELEASE DOES NOT AUTHORIZE ANY WORK IN *JJ
CONRICT WITH THE BUILDING CODE OR ZONING OR ... f..../ N
J ES VI CI
CITY APPROVED PLANS TO BE KEPT OIL 1
2 ,Sso .: REVISIONS:
THE JOB SITE AT ALL TIMES t�ss►ONALG`��~
MAX AVAILABLE BACKFEED FOR SES BUS SIZE:
200A BUS x 1.2 = 240A - 175A BREAKER =
65A BACKFEED AVAILABLE
MAX BACKFED CURRENT FOR OCPD:
42A x 1.25 = 52.5A TOTAL
DATE: -Ai;2 l � BY: �' 06-28-2019
TR CTUR, ONLY
BUIL ING INSPECTION DIVISION:
RELEASE DOES NOT APPLY TO CONSTRUCTION IN
EASEMENTS OR PUBLIC RIGHT-OF-WAY.
ALL CHANGES MUST BE APPROVED
DRAWN BY: ND
DATE: 06/29/2019
WIRING
CALCULATIONS
SHEET: 3
cSfrucfurai �in9in eers
vincise.com
TOPE Frtn Rego ho, No F 20604
SINGLE LINE DIAGRAM
(6x) #10 AWG
& (lx) #8 AWG GROUND
(THWN-2/PV WIRE)
(SEE NOTE #4)
(12x) MISSION SOLAR ENERGY
MSE310SQ8T
WITH (12x) P320 POWER OPTIMIERS
(FOR GROUNDING SEE NOTE #5)
(12x) MISSION SOLAR ENERGY
MSE310SQ8T
WITH (12x) P320 POWER OPTIMIERS
(FOR GROUNDING SEE NOTE #5)
I
(12x) MISSION SOLAR ENERGY
MSE3IOSQ8T
WITH (12x) P320 POWER OPTIMIERS
(FOR GROUNDING SEE NOTE #5)
MAX AVAILABLE BACKFEED FOR SES BUS SIZE:
200A BUS x 1.2 = 240A - 175A BREAKER =
65A BACKFEED AVAILABLE
MAX BACKFED CURRENT FOR OCPD:
42A x 1.25 = 52.5A TOTAL
INVERTER A
SOLAREDGE
SE10000H-US
(W/ DC
DISCONNECT
INTEGRATED INTO
INVERTER & DC
AFCI COMPLIANT
TO UL 1699B)
3/4" EMT
(3x) #6 AWG
& (Ix) #8 AWG GROUN
D(THWN-2 WIRE)
60A VISIBLE
LOCKABLE UTILITY
AC DISCONNECT
SWITCH
EATON CUTLER
HAMMER DG221 URB
240V - NON FUSED -
SERVICE ENTRANCE
RATED
INTEGRATED RGM #8 CU BARE GROUNDING ELECTRODE
(RAPID CONDUCTOR (GEC). TO RUN
SHUTDOWN) INDEPENDENTLY OF OTHER CONDUCTORS
AND TIE DIRECTLY INTO AC GROUNDING
ELECTRODE
v
EXISTING 200A
PANEL & METER
(PANEL INSIDE
AND METER ON
OUTSIDE WALL)
BI-DIRECTIONAL
SINGLE PHASE
M
UTILITY METER
NEW 175A MAIN
L BREAKER
(DERATED FROM
200A)
60A PV BREAKER
(SEE NOTE #1 FOR
[� LOCATION)
LL
GROUNDING ELECTRODE
(SEE ELECTRICAL NOTES 98)
ELECTRICAL NOTES
1. THE PHOTOVOLTAIC CONNECTION IN THE PANEL BOARD
SHALL BE POSITIONED AT THE OPPOSITE (LOAD) END FROM
THE INPUT FEEDER LOCATION OR MAIN CIRCUIT LOCATION
PER NEC ART. 705.12(D)(7) WHEN USING THE 120% OF RATING
ALLOWANCE FOR DETERMINING THE TOTAL RATING OF OVER
CURRENT DEVICE.
2. IDENTIFICATION AND GROUPING OF PHOTOVOLTAIC DC
CIRCUITS SHALL COMPLY WITH NEC 690.4(B) AND SHALL BE
SEPARATED FROM OTHER NON PV SYSTEM CONDUCTORS.
3. EXPOSED NON -CURRENT CARRYING METAL PARTS OF
PHOTOVOLTAIC RACKING, EQUIPMENT, AND CONDUCTOR
ENCLOSURES SHALL BE GROUNDED IN ACCORDANCE TO NEC
690.47 (C)(3), 250.64(C), 250.66, & 250.134 OR 250.136(A) AND
SIZED PER 250.166 REGARDLESS OF VOLTAGE.
4. ALL CONDUIT ON ROOF NEEDS TO BE PLACED 1 /2"-3 1/2" OFF
THE ROOF'S SURFACE.
5. EACH MODULE (AND MICRO -INVERTER, IF APPLICABLE)
SHALL BE GROUNDED PER THE MANUFACTURER'S
INSTRUCTIONS USING THE BONDING MIDCLAMP /
COMPONENTS, AND AT EACH ROW UTILIZING AMPHENOL
HELIO LUGS (UL 2703). SPEC SHEETS CAN BE PROVIDED UPON
REQUEST.
6. ELECTRICAL EQUIPMENT INSTALLED SHALL BE LISTED,
LABELED, OR CERTIFIED FOR ITS USE BY A NATIONALLY
RECOGNIZED TESTING LABORATORY (NRTL).
7. ALL TERMINATIONS OF EQUIPMENT TO BE A MINIMUM 75
DEGREE CELCIUS PER NEC 110.14(C) & TABLE 310.15 (13)(16) 75
DEGREE COLUMN COPPER.
8. FOR SERVICE UPGRADES, IF THE EXISTING GROUNDING
ELECTRODE SYSTEM CAN NOT BE VERIFIED, OR IS ONLY
METALLIC WATER PIPING, OR IT HAS A RESISTANCE GREATER
THAN 25 OHMS, IT IS THE CONTRACTOR'S RESPONSIBILITY TO
INSTALL A SUPPLEMENTAL GROUNDING ELECTRODE AT
LEAST 6' FROM THE EXISTING GROUNDING ELECTRODE.
9. ALL BREAKERS AND SERVICE EQUIPMENT ARE RATED AT
22kAIC OR HIGHER
10. GROUND BUSHINGS TO BE USED ON ALL METALLIC
RACEWAYS.
CITY OF GRAPEVINE
RiLEASED FOR CONSTRUCTION
SHEET: S OF:
RELEASE DOES NOT AUTHORIZE ANY WORK IN
CONFLICT WITH THE BUILDING CODE OR ZONING ORDINANCE.
CITY APPROVED PLANS TO BE KEPT ON
THE JOB SITE AT ALL TIMES
DATE: 5 94ac BY: a'
BUILDING INSPECTION DIVISION:
RELE ESE DOES NOT APPLY TO CONSTRUCTION IN
ASEMENTS OR PUBLIC RIGHT-OF-WAY.
ALL CHANGES MUST BE APPROVED
U
o
W
�
N
aIN�raN
00
O
"
0
p ,-� W
—.4
N
O
t`
w
V
G� a�
V
0 Poo
C�
*P.4
� o
� o
a
O
0
N
REVISIONS:
DRAWN BY: ND
DATE: 06/28/2019
SINGLE LINE
DIAGRAM
SHEET: 4
ARRAY DIAGRAM
---+ _ 1+• - -+ -
• • +----------
ARRAY 1
(12x) MISSION SOLAR ENERGY MSE310SQ8T
WITH (12x) P320 POWER OPTIMIZERS
(FOR GROUNDING SEE NOTE #5)
+ _
— 4- -
- + L - —
ARRAY 2
(12x) MISSION SOLAR ENERGY MSE3I OSQ8T
WITH (12x) P320 POWER OPTIMIZERS
(FOR GROUNDING SEE NOTE #5)
rr
■
•-------------�
+ =
1 +
-+ _ — -
ARRAY 3
(12x) MISSION SOLAR ENERGY MSE310SQ8T
WITH (12x) P320 POWER OPTIMIZERS
(FOR GROUNDING SEE NOTE #5)
rr
((
•
- -■
-----------
MAX AVAILABLE BACKFEED FOR SES BUS SIZE:
200A BUS x 1.2 = 240A - 175A BREAKER =
65A BACKFEED AVAILABLE
MAX BACKFED CURRENT FOR OCPD:
42A x 1.25 = 52.5A TOTAL
------------�---
- -9- v 19
---------- 4-------------•--------------
n
+
(6x) #10 AWG
& (lx) #8 AWG GROUND
(THHN-2/THWN-2/PV WIRE)
(SEE NOTE #4)
ELECTRIC AL NOTES
0
1.
THE PHOTOVOLTAIC CONNECTION IN THE PANEL BOARD
'
SHALL BE POSITIONED AT THE OPPOSITE (LOAD) END FROM
v
THE INPUT FEEDER LOCATION OR MAIN CIRCUIT LOCATION
PER NEC ART. 705.12(D)(7) WHEN USING THE 120% OF RATING
O d1
N
ALLOWANCE FOR DETERMINING THE TOTAL RATING OF OVER
OO
CURRENT DEVICE.
N
O M
2.
IDENTIFICATION AND GROUPING OF PHOTOVOLTAIC DC
CIRCUITS SHALL COMPLY WITH NEC 690.4(B) AND SHALL BE
p O
SEPARATED FROM OTHER NON PV SYSTEM CONDUCTORS.
O CCj
a
3.
EXPOSED NON -CURRENT CARRYING METAL PARTS OF
PHOTOVOLTAIC RACKING, EQUIPMENT, AND CONDUCTOR
-�
ENCLOSURES SHALL BE GROUNDED IN ACCORDANCE TO NEC
690.47 (C)(3), 250.64(C), 250.66, & 250.134 OR 250.136(A) AND
CI
SIZED PER 250.166 REGARDLESS OF VOLTAGE.
4.
ALL CONDUIT ON ROOF NEEDS TO BE PLACED 1/2"-3 1/2" OFF
THE ROOF'S SURFACE.
5.
EACH MODULE (AND MICRO -INVERTER, IF APPLICABLE)
SHALL BE GROUNDED PER THE MANUFACTURER'S
INSTRUCTIONS USING THE BONDING MIDCLAMP /
>
COMPONENTS, AND AT EACH ROW UTILIZING AMPHENOL
V
N
HELIO LUGS (UL 2703). SPEC SHEETS CAN BE PROVIDED UPON
W
U U
REQUEST.
1-I
6.
ELECTRICAL EQUIPMENT INSTALLED SHALL BE LISTED,
!04
W
LABELED, OR CERTIFIED FOR ITS USE BY A NATIONALLY
RECOGNIZED TESTING LABORATORY
�y x
(NRTL).
7.
ALL TERMINATIONS OF EQUIPMENT TO BE A MINIMUM 75
O
O W
DEGREE CELCIUS PER NEC It 0. 14(C) & TABLE 310.15 (B)(16) 75
~ ~
DEGREE COLUMN COPPER.
�y
a
�
8.
FOR SERVICE UPGRADES, IF THE EXISTING GROUNDING
ELECTRODE SYSTEM CAN NOT BE VERIFIED, OR IS ONLY
METALLIC WATER PIPING, OR IT HAS A RESISTANCE GREATER
THAN 25 OHMS, IT IS THE CONTRACTOR'S RESPONSIBILITY TO
INSTALL A SUPPLEMENTAL GROUNDING ELECTRODE AT
'--i
LEAST 6' FROM THE EXISTING GROUNDING ELECTRODE.
O
9.
ALL BREAKERS AND SERVICE EQUIPMENT ARE RATED AT
22kAIC OR HIGHER
10.
GROUND BUSHINGS TO BE USED ON ALL METALLIC
RACEWAYS.
CITY OF GRAPEVINE
RELEASED FOR CONSTRUCTION
SHEF7: OF:
RELEASE DOES NOT AUTHORIZE ANY WORK IN
OONRICT'NffH THE BUILDING CODE OR ZONING ORDINANCE.
CITY PPROVED PLANS TO BE KEPT ON
THE JOB SITE AT ALL TIMES
DATE: XI t ao BY:
BUILDING INSPECTION DIVISION:
RELEA 5E DOES NOT APPLY TO CONSTRUCTION IN
EkSEMENTS OR PUBLIC RIGHT-OF-WAY.
ALL CHANGES MUST BE APPROVED
.�
•F"
.F" 'd
cl a$
0
.F
� o
� o
a
0
0
N
REVISIONS:
DRAWN BY: ND
DATE: 06/28/2019
ARRAY
DIAGRAM
SHEET: 5
THREE LINE DIAGRAM
INVERTER
SOLAREDGE
SE10000H-US
WITH INTEGRATED DC DISCONNECT AND DC
COMBINER
AFCI COMPLIANT TO UL1699B
(INTEGRATED RGM (RAPID SHUTDOWN))
+ �� + + DC L2
+ + AC N
J
3/4" EMT
(6x) #10 AWG
& (Ix) #8 AWG GROUND
(THHN-2/THWN-2/PV WIRE)
(SEE NOTE #4)
GFPD G
a
3/4" EMT
(3x) #6 AWG
& (Ix) #8 AWG GROUND
(THHN-2/THWN-2 WIRE)
---------- G• - -
+
60A VISIBLE LOCKABLE
UTILITY AC DISCONNECT
SWITCH
EATON CUTLER HAMMER
DG22IURB 240V - NON
FUSED - SERVICE
ENTRANCE RATED
#8 CU BARE GROUNDING ELECTRODE
CONDUCTOR (GEC). TO RUN INDEPENDENTLY
OF OTHER CONDUCTORS AND TIE DIRECTLY
INTO AC GROUNDING ELECTRODE
MAX AVAILABLE BACKFEED FOR SES BUS SIZE:
200A BUS x 1.2 = 240A - 175A BREAKER =
65A BACKFEED AVAILABLE
MAX BACKFED CURRENT FOR OCPD:
42A x 1.25 = 52.5A TOTAL
ELECTRICAL NOTES
O
1. THE PHOTOVOLTAIC CONNECTION IN THE PANEL BOARD
'
SHALL BE POSITIONED AT THE OPPOSITE (LOAD) END FROM
v
THE INPUT FEEDER LOCATION OR MAIN CIRCUIT LOCATION
r T l
PER NEC ART. 705.12(D)(7) WHEN USING THE 120% OF RATING
w Q1
ALLOWANCE FOR DETERMINING THE TOTAL RATING OF OVER
ONO
CURRENT DEVICE.
N
O M
2. IDENTIFICATION AND GROUPING OF PHOTOVOLTAIC DC
v'
CIRCUITS SHALL COMPLY WITH NEC 690.4(B) AND SHALL BE
p O rA
SEPARATED FROM OTHER NON PV SYSTEM CONDUCTORS.
N
3. EXPOSED NON -CURRENT CARRYING METAL PARTS OF
� O
a
PHOTOVOLTAIC RACKING, EQUIPMENT, AND CONDUCTOR
ENCLOSURES SHALL BE GROUNDED IN ACCORDANCE TO NEC
I ��
690.47 (C)(3), 250.64(C), 250.66, & 250.134 OR 250.136(A) AND
�I
�1
SIZED PER 250.166 REGARDLESS OF VOLTAGE.
r
4. ALL CONDUIT ON ROOF NEEDS TO BE PLACED 1/2"-3 1/2" OFF
THE ROOF'S SURFACE.
5. EACH MODULE (AND MICRO -INVERTER, IF APPLICABLE)
SHALL BE GROUNDED PER THE MANUFACTURER'S
INSTRUCTIONS USING THE BONDING MIDCLAMP /
r 1 >
C)
COMPONENTS, AND AT EACH ROW UTILIZING AMPHENOL
W
EXISTING 200A
HELIO LUGS (UL 2703). SPEC SHEETS CAN BE PROVIDED UPON
U N
METER &PANEL
REQUEST
Q+ Q N
DIRECTIONAL
a
r SINGLE PHASE
6. ELECTRICAL EQUIPMENT INSTALLED SHALL BE LISTED,
Q
W
UTILITY METER
M
LABELED, OR CERTIFIED FOR ITS USE BY A NATIONALLY
RECOGNIZED TESTING LABORATORY
o 44 �
I� ul
<
(NRTL).
P-
NEW 175A MAIN
- BREAKER
7, ALL TERMINATIONS OF EQUIPMENT TO BE A MINIMUM 75
O O a
- - _ _ ,
DEGREE CELCIUS PER NEC 110.14(C) & TABLE 310.15 (B)(l6) 75
- - - - - - - �. (DEBATED FROM
DEGREE COLUMN COPPER.
�y
W
-, 200A)
a
18. FOR SERVICE UPGRADES, IF THE EXISTING GROUNDING
NEW 60A PV BREAKER
ELECTRODE SYSTEM CAN NOT BE VERIFIED, OR IS ONLY
1 - ' (SEE NOTE #1 FOR
METALLIC WATER PIPING, OR IT HAS A RESISTANCE GREATER
LOCATION)
THAN 25 OHMS, IT IS THE CONTRACTOR'S RESPONSIBILITY TO
INSTALL A SUPPLEMENTAL GROUNDING ELECTRODE AT
N _
LEAST 6' FROM THE EXISTING GROUNDING ELECTRODE.
9. ALL BREAKERS AND SERVICE EQUIPMENT ARE RATED AT
GROUNDING ELECTRODE
22kAIC OR HIGHER
(SEE NOTE 48)
V [�
10. GROUND BUSHINGS TO BE USED ON ALL METALLIC
RACEWAYS.
4
�I
CITY OF GRAPEVINE
0
FEELEASED FOR CONSTRUCTION
r
7
�, o
a
S ET: OF: �s
R SE DOES NOT AUTHORIZE ANY WORK IN
o
CONRXT WITH THE BUILDING CODE OR ZONING ORDINANCE.
N
CITY APPROVED PLANS TO BE KEPT ON
THE JOB SITE AT ALL TIMES
REVISIONS:
DATE:. 2 .2f 2-0 BY:
BUILDING INSPECTION DIVISION:
RELI EASE DOES NOT APPLY TO CONSTRUCTION IN
DRAWN BY: ND
I EASEMENTS OR PUBLIC RIGHT-OF-WAY.
DATE: 06/28/2019
ALI. CHANGES MUST BE APPROVED
THREE LINE
-
DIAGRAM
SHEET5.1
THIS LABEL TO BE INSTALLED AT DISTRIBUTION
EQUIPMENT (MAIN SERVICE PANEL, PV SOLAR
COMBINER PANELBOARD, AC DISCONNECT)
(NEC 690.53, & 690.54)
MAX RATED AC OUTPUT OPERATING CURRENT: 42 A
OPERATING AC VOLTAGE: 240VAC
THIS LABEL TO BE INSTALLED INVERTER
(PV POWER SOURCE INFORMATION (NEC 690.53, & 690.54)
THIS LABEL TO BE INSTALLED AT PHOTOVOLTAIC
INVERTER OR GROUND FAULT INDICATOR
(PER NEC 690.5(C))
WARNING
ELECTRIC SHOCK HAZARD
IF A GROUND FAULT IS INDICATED,
NORMALLY GROUNDED CONDUCTORS MAY
BE UNGROUNDED AND ENERGIZED
THIS LABEL TO BE INSTALLED AT
PV COMBINER PANELBOARD
RATED MAX POWER POINT CURRENT: 29.4 ADC WARNING
RATED MAX POWER POINT VOLTAGE: 380 VDC PHOTOVOLTAIC SOLAR ONLY.
MAX SYSTEM VOLTAGE: 480 VDC NO ADDITIONAL LOADS ALLOWED
SHORT CIRCUIT CURRENT: 15 ADC
THIS LABEL TO BE INSTALLED AT DISTRIBUTION
EQUIPMENT (MAIN SERVICE PANEL, PV SOLAR
COMBINER PANELBOARD)
WARNING
THIS EQUIPMENT FED BY MULTIPLE SOURCES.
TOTAL RATING OF ALL OVERCURRENT
DEVICES, EXCLUDING MAIN SUPPLY
OVERCURRENT DEVICE, SHALL NOT EXCEED
AMPACITY OF BUSBAR
THIS LABEL TO BE INSTALLED AT DISTRIBUTION
EQUIPMENT (MSP, PV SOLAR
COMBINER PANELBOARD) ADJACENT TO THE
INVERTER BACK -FED BREAKER
WARNING
INVERTER OUTPUT
CONNECTION
THIS LABEL TO BE INSTALLED AT THE
ENERGIZED DISCONNECTING MEANS.
(PER NEC 690.13(B), NEC 690.15, NEC
CAUTION: PHOTOVOLTAIC ELECTRIC SYSTEM CONNECTED
THIS LABEL TO BE INSTALLED AT THE
PV DISCONNECTING MEANS.
(PER NEC 690.15, IFC 605.11.1, & IFC 605.11.1.4.
PHOTOVOLTAIC
AC DISCONNECT
THIS LABEL TO BE INSTALLED WHERE ALL
TERMINALS OF THE DISCONNECTING MEANS
MAY BE ENERGIZED IN THE OPEN POSITION
(PER NEC 690.17(E))
WARNING - ELECTRIC SHOCK HAZARD
DO NOT TOUCH TERMINALS. TERMINALS ON
BOTH THE LINE AND LOAD SIDES MAY BE
ENERGIZED IN THE OPEN POSITION.
THIS LABEL TO BE INSTALLED AT EACH AND EVERY
JUNCTION BOX, COMBINER BOX, AC/DC DISCONNECT,
AND EVERY DEVICE WHERE UNGROUNDED CIRCUITS MAY
BE EXPOSED DURING SERVICE (PER NEC 690.35(F))
WARNING - ELECTRIC SHOCK HAZARD
THE CURRENT CIRCUIT CONDUCTORS OF THIS
PHOTOVOLTAIC POWER SYSTEM ARE UNGROUNDED
BUT MAY BE ENERGIZED WITH RESPECT TO GROUND
DUE TO LEAKAGE PATHS AND/OR GROUND FAULTS
THIS LABEL SHALL APPEAR AT EVERY SECTION OF THE
WIRING SYSTEM THAT IS SEPERATED BY ENCLOSURES,
WALLS, PARTITIONS, CEILINGS OR FLOORS.
SPACING BETWEEN LABELS NOT TO EXCEED 10 FEET
(NEC 690.3 1 (G)(3), IFC 605.11.1.2)
►,/:�:i.l ►[e3ii:[�yC�Pl�7N��[�lZ�]� I�:��ili:t�
THIS LABEL TO BE INSTALLED AT THE
ENERGIZED DISCONNECTING MEANS.
(PER NEC 690.15 & NEC 690.53,
IFC 605.11.1, & IFC 605.11.1.4)
MAIN PV SYSTEM
DISCONNECT
THIS LABEL TO BE AT THE
MAIN ELECTRICAL SERVICE PANEL.
(PER NEC 690.56(C)(L)A
PHOTOVOLTAIC SYSTEM
EQUIPPED WITH RAPID
SHUTDOWN
PERMANENT SIGNAGE NOTES
1. ALL LABELS / PLAQUES AND SIGNAGE IS REQUIRED
BY THE 2017 EDITION OF THE NATIONAL ELECTRICAL
CODE AS REQUIRED. PROVIDE ALL WARNING,
LABELS AND MARKINGS AS REQUIRED IN THE 2017
NEC.
2. PROVIDE ALL LABELS, CODE REFERENCES AND
SPECIFICATIONS IN COMPLIANCE WITH 2O17 NEC
ARTICLE 690 NEC SOLAR PHOTOVOLTAIC AND
ARTICLE 705 INTERCONNECTED ELECTRIC POWER
PRODUCTION SYSTEM.
3. PROVIDE WARNINGS, LABELS, MARKINGS AND THE
LOCATION WHERE THEY SHALL BE INSTALLED, AS
SPECIFIED IN ARTICLE 690 NEC, 705 FOR SOLAR
PHOTOVOLTAIC SYSTEMS.
4. EQUIPMENT SHALL BE INSTALLED IN ACCORDANCE
WITH THE 2017 NEC AND ALL APPLICABLE
REQUIREMENTS OF THE SERVING ELECTRIC UTILITY
COMPANY AND OF THE LOCAL AUTHORITY HAVING
JURISDICTION
5. LABEL BREAKER "PHOTOVOLTAIC ELECTRIC POWER
SOURCE" PER NEC 705.10 AND 'BREAKERS ARE
BACKFED" PER 690-64(B)(5). LABEL MAXIMUM A/C
OUTPUT OPERATING CURRENT AND OPERATING
VOLTAGE PER NEC 690.54
6. LABEL "PHOTOVOLTAIC SYSTEM UTILITY
DISCONNECT SWITCH", SWITCH COVER TO BE
LOCKED AT ALL TIMES, SWITCH TO BE ACCESSIBLE
PER UTILITY REQUIREMENTS AND CONFORM TO NEC
705.22
7. LABEL "PHOTOVOLTAIC POWER SYSTEM DEDICATED
KWH METER"
8. PROVIDE WARNING SIGN PER NEC 690.17 READING
"WARNING -ELECTRIC SHOCK HAZARD -DO NOT
TOUCH TERMINALS- TERMINALS ON BOTH LINE AND
LOAD SIDES MAY BE ENERGIZED IN THE OFF
POSITION.
9. LISTING AGENCY NAMES AND NUMBERS TO BE
INDICATED ON POWER INVERTER AND SOLAR
MODULES PER NEC 110.3(B)
10. METALLIC CONDUIT SHALL BE USED WITHIN
MWOw &E)
RE�,�'� $ED JCTMOMBINER
PA (IF USED , AD DO NOT AD S TO THIS PANEL
SHEE f : F:
RELE, kSE DOESFINMAUlt4DRFICATION,
OONRJCT V IITH THE "MWGSWDffopVoNWWoRDNVMEG.
'PROVED PLANS TO BE KEPT ON
THE JOB SITE AT ALL TIMES
DATE: -2/911= BY: 5;1-?•
BUIL61NG INSPECTION DIVISION:
RELEA: iE DOES NOT APPLY TO CONSTRUCTION IN
E►SEMENTS OR PUBLIC RIGHT-OF-WAY.
ALL 01HANGES MUST BE APPROVED
V
W
7
•--{ �--�
hey
w �
REVISIONS:
DRAWN BY: ND
DATE: 06/28/2019
PLACARDS
SHEET: 6
N_
00
0
'4
PHOTOVOLTAIC
SYSTEM SIE:STANDARD ECO
9 Brittain Residence
10.00 kW AC 110 E. Houston St.,
2600 Pool Road Grapevine, TX 76051 11.16 kW DC San Antonio, TX 78205
SINGLE PHASE 120V/240V TX License #:32439
solar=ee
SolarEdge Power Optimizer
Module Add -On For North America
P300 / P320 / P370 / P400 / P405
PV power optimization at the module -level
— Up to 25% more energy
- Superior efficiency (99.5%)
- Mitigates all types of module mismatch losses, from manufacturing tolerance to partial shading
— Flexible system design for maximum space utilization
- Fast installation with a single bolt
— Next generation maintenance with module -level monitoring
— Module -level voltage shutdown for installer and firefighter safety
USA dge.us
solar=@@ SolarEdge Power Optimizer
Module Add -On for North America
P300 / P320 / P370 / P400 / P405
P370
P300 P320
P400 P405
for 60-cell mad- for high -power
( (for
(for higher -power
72 & 96-cell {for thin film
ules) 60-cell modules)
60 and cell modules) modules)
— -_,—
le
modules) _ —
INPUT
Rated Input DC Powerl'!
............................
300 320
_
W
Absolute Maximum Input Voltage
..................370..................400........
........405.....
.........
(Voc at lowest temperature)
48 60 80
125
Vdc
MPPT Operating Range
8 - 48 8 - 60 8 - 80
......................................
12.5 - 105
..................
Vdc
Maximum Short Circuit Current...I.
.............................n't(Is..................-..........I..,..........
10 11 10:1
... ...........................
Adc.....
Maximum DC Input Current
..............I................1...................................
12.5 E 13:75 12:63
Adc
Maximum Efficiency
99.5
%
Wei hted Eff cienc
......g....--..I ............................
98.8
%
...
Overvoltage Category_
_ _ _ _ _ _ _ _ II
OUTPUT DURING OPERATION (POWER OPTIMIZER CONNECTED TO OPERATING SOLAREDGE INVERTER)
Maximu.m Output Current
15
A dc
.
.......
Maximum Output Voltage
...........................
.._oltage _ 60 ,
Vdc_
_85
OUTPUT DURING STANDBY (POWER OPTIMIZER DISCONNECTED FROM SOLAREDGE INVERTER OR SOLAREDGE INVERTER OFF)
_
Safety Output Voltage per Power
_Optimizer
�- -- - - - -- -- -- - 1 - -
Vdc
STANDARD COMPLIANCE
EMC
-..-.1.............................
FCC Part15 Class B, IEC61000-6-2, IEC61000-6-3
..-.-.-..-.--..
..............
Safety ...... .......
.......... ............... ....................................
............... ......... IEC62109-1 (class ll safety), UL1741
_RoHS _ _ _
Yes
-INSTALLATION SPECIFICATIONS
- — — �— —
Maximum Allowed System Voltage
1000
Vdc
Compatible inverters
All SolarEdge Single Phase and Three Phase inverters
Dimensions (W x L x H)
128x152x35/
128 x 152 x 27.5 / 5 x 5.97 x 1.08
128x152'x50/
mm / in
Sx5.97x1.37
5x5.97x1.96
Weight (including cables)
630 / 1;4 750 / 1.7
.. ....................................................................
845 / 1.9
gr / Ib
MC4 /
Input Connector
MC4 Compatible
Amphenol AH4MC4 Compatible
..... ... .................. I
.
Double Insulated;
Output Wire Type / Connector
Double Insulated; MC4 Compatible MC4 / Double Insulated; MC4 Compatible
Amphenol AH4
Output Wire Length
.........
0 95 j 3 0 1.2 / 3 9
m/ ft
Operatin�TemperatureRanpe
_.........
-40-+85/ 40-+185
"C/'F
Protection .Rating
............. ......... .
IP68 / NEMA6P
Relative Humidity
0 - 100
%
("Rated STC power of the module. Module of up to+5%power
tolerance allowed.
PV SYSTEM DESIGN USING _
SINGLE PHASE
A SOLAREDGE INVERTER(21(3)
SINGLE PHASE THREE PHASE 208V THREE PHASE 480V
HD -WAVE
Minimum String Length
(Power Optimizers)
g 10 18
Maximum String Length
(Power Optimizers)
25 25 50
5700 (6000 with
Maximum Power per String
5250 6000 12750
W
Parallel Strings of Different Lengths
or Orientations
.............................................................................................
Yes
.
4'1 For detailed string sizing information refer to: http://www.sulareclge.com/sites/default/files/string_sizing_na.pdf
''it is not allowed to mix P405 with P300/P370/P400/P600/P700 in one string
solar =@"
Single Phase Inverter
with HD -Wave Technology
for North America
SE3000H-US / SE380OH-US / SE5000H-L
SE6000H-US / SE760OH-US / SE10000H-
solar m.
"wart#'-
r� e�
WattanW
g ,
44
!
Optimized installation with HD -Wave technology
Specifically designed to work with power optimizers
Record -breaking efficiency
Fixed voltage inverter for longer strings
Integrated arc fault protection and rapid shutdown for NEC 2014 and 2017, per article 690.11 and 690.12
UL1741 SA certified, for CPUC Rule 21 grid compliance
Extremely small
— High reliability without any electrolytic capacitors �,�
— Built-in module -level monitoring
— Outdoor and indoor installation wave
— Optional: Revenue grade data, ANSI C12.20 Class 0.5 (0.5% accuracy)
www.solaredge.us
solar=@@Single Phase Inverter
with HD -Wave Technology for North America
SE3000H-US / SE380OH-US / SE5000H-US /
SE6000H-US/ SE760OH-US / SE1000OH-US / SE1140OH-US
_
SE3DOOH-US I 0H SE380-US SESOOOH-US
---
SE6000H_US
SE760OH-US ! SE10000H-US SE1140OH-US
OUTPUT
- - ---
- - -
- --- ---
Rated AC Power Output
3000
3800 @ 240V 5000
6000 @ 240V
7600 10000
11400
VA
...... ._.
,3..... . 08V
5000 �,208V,
Max. AC Power Output
3000
3800 @ 240V
5000
6000 @ 2401!
7600 10000
11400
VA
3300. 208y.................
. 5000 @, 208V,
............. .
................
AC Output Voltage Min.-Nom: Max.
�
(183-208 Z29)
_
Vac
..........................
AC Output Voltage Min.-Nom: Max.
.
Vac
(211.; 240 - 264)...........................
1................�............ .
...
AC Frequency (Nominal) ...............
59.3.:60.:60:51'..,........
Hz
Maximum Continuous Output Current
.....................
208V.....................................
16
24
A
Maximum Continuous Output Current
240V......
12.5
16 21
...............
25
............................
32 42
......
47.5
...........
A
GFDI Threshold
1
A
Utility�Nloriitoring, Islencl�ing�Proti=ction,
..................
CountEyCon K!!rableThresholds-_L____
___- —_
Yes
INPUT
Maximum DC Power @240V
...........................................................................................
1 4650 5900
7750
9300 11800 15500
17650 W
Maximum DC Power @208V
5100
....,.,,..............,.. ...............................
7750 -
........
Transformer -less, Un rounded
�....................
Maximum In ut Volta a
!?........�................
....,Yes ...................
480
Vdc
Nominal DC Input Voltage
...
380
400
Vdc
Maximum Input Current 208V
9 (
13 5
Maximum Input Current @240V......
............................
8:5...........105......1.....
.......... .....
135......
�......165......1...... ZO.. ??
Max. Input Short Circuit Current
.............
.............30:5.....
45
Adc
Reverse -Polarity Protection
.. .. ..
..................
Yes
Ground -Fault Isolation Detection
..................2..........................................
600kn Sensitivity
Maximum Inverter Efficiency
99
99.2
%
CEC Wei hted Efficiency
....................................................,.............
99
.... .,.,
30
Nighttime Power Consumption—
W
ADDITIONAL FEATURES
Supported Communication Interfaces RS485, Ethernet, ZigBee (o tional), Cellular o tional
......... ............................. P.................. I . P....... )..
Revenue Grade Data, AN51 C12,20 OptionaliZl
..........................
Rapid Shutdown - NEC 2014 and 2017
690 12 Automatic Rapid Shutdown upon AC Grid Disconnect
STANDARD COMPLIANCE
-
-
Safety
UL1741, UL1741 SA, UL16998, CSA C22:2: Canadian AFCI according to T.I. L; M .07_
Grid Connection Standards
IEEE1547, Rule 21, Rule 14 (HI)
...................14(H..................................
Emissions _ _
FCC Part_15 Class B
... .........
INSTALLATION SPECIFICATIONS
_
_
AC Output Conduit Size / AWG Range
3/4" minimum / 14-6 AWG
minimum /14-4 AWG
DC Input Conduit Size / # of Strings /
3/4" minimum / 1-2 strings / 14-6 AWG
3/4" minimum / 1-3 strings /
AWG,Rang? ...............................
AVVG............
Dimensions with Safety Switch (HxWxD)
........ ............14:6
17.7 x 14.6 x 6.8 / 450 x 370 x 174
21.3 x 14.6 x 7.3 % 540 x 370
. .
in / mm
x 185
..............................
Weight with Safety Switch
............. ................
22 / 10 25.1 / 11.4 i 26.2 / 11.9
38.8 / 17.61.
Ib k
Noise ..................................
<25
...............................................
<50
dBA
Cooling
Natural Convection
................................................
Natural convection
Operating Temperature Range
..•
13 to +140 / 25 to +60i31 (40`F % :40'C option)I"i,.
.
F / ..
Protection Rating
NEMA 3R (Inverter with Safety Switch)
Itl For other regional setngs please contact SolarEdge support
1�1 Revenue grade inverter P/N: SExxxxH-US000NK2
iat For power de -rating information refer to: https://www,solaredge.com/sites/default/files/se-temperature-derating-note-na.pdf
i4i -40 version P/N: SE—H-US000NN1.14
FM
U a:i�.11
CERTIFIED RELIABILITY
> Tested to UL1703 & IEC standards
> PID Resistant
SUPERIOR AESTHETICS
> All -black design coupled with outstanding power output
> Ideal for residential & commercial applications
13 EXTREME WEATHER RESILIENCE
> 5631 Pa snow load (117 psf) tested load to UL1703
> 185 mph wind rating*
BAA COMPLIANT FOR GOVERNMENT PROJECTS
> Buy American Act
)American Recovery & Reinvestment Act
I
AP
LINEAR WARRANTY PRODUCT WARRANTY
300-qlOW 100%
97%
Mission Solar Energy Warranty
j 90.7%
CLASS LEADING POWER OUTPUT 90% o
80.2%!
80%
I
18.6 / 70%
MAXIMUM EFFICIENCY 1 5 10 15 20 25
YEARS
_0,il + 3 940
POSITIVE POWER TOLERANCE
High -Power, American Quality
Mission Solar Energy is headquartered in San Antonio, TX with module
facilities onsite. We produce American quality poducts ensuring the
highest power output and reliability to our customers. Our product line
is well suited for residential, commercial and utility applications. Every
Mission Solar Energy product is certified and surpasses industry
standard regulations, proving excellent performance over the long-term.
www.missionsolar.com I info@missionsolar.com
CERTIFICATIONS
IEC 61215/ IEC 61730/ IEC 61701 UL 1703
-�', I:l us PQw�r�uard CEC
\_:-
LISTED
'As there are different certification requirements in different markets, please contact your local
Mission Solar Energy sales representative for the specific certificates applicable to the products in
the region in which the products are to be used.
`185 mph wind rating based upon installation at 30* or less fixed tilt mount
TM
MISSION SOLAR 0i
ENERGY ■0 11
PERC 60
SPECIFICATIONS
.ELECTRICAL
Electrical Parameters at Standard Test Conditions (STC)
Module Type
MSE300SQST
MSE305SQBT
MSE310SQ8T
Power Output
Pmax
Wp
300
305
310
Module Efficiency
%
18.05
18.35
18.65
Tolerance
0-+3%
0-+3%
0-+3%
Short -Circuit Current
Isc
A
9.571
9.664
9.760
Open Circuit Voltage
Vac
V
40.08
40.10
40.12
Rated Current
Imp
A
9.058
9.202
9.345
Rated Voltage
Vmp
V
33.12
33.14
33.17
Fuse Rating
15
20
20
Normal Operating Cell Temperature (NOCT)
46.09*C (±2°C)
Temperature Coefficient of Pmax
-0.377%/°C
Temperature Coefficient of Voc
-0.280%/*C
Temperature Coefficient of Isc
0.039%/°C
Log i.g a11►+ tl�
Maximum System Voltage 1,000VDC
Operating Temperature Range -40°C (-400F) to +85°C (185*F)
Maximum Series Fuse Rating 20A
Fire Safety Classification Class C
Front &Back Load (UL standard) 5631Pa (117 psf) Tested toUL1703 standard
Hail Safety Impact Velocity 25mm at 23 m/s
Solar Cells P-type Mono -crystalline Silicon (156.75mm)
Cell orientation 60 cells (6x10), 5 busbar
Module dimension 1664mm x 999mm x 40mm
(65.53 in. x 39.33 in. x 1.58 in.)
Weight 18.2 kg (40.1 lb)
Front Glass 3.2mm (0.126 in.) tempered,
Low -iron, Anti -reflective coating
Frame Anodized aluminum alloy
Encapsulant Ethylene vinyl acetate (EVA)
J-Box Protection class IP67 with 3 bypass -diodes
Cables PV wire, 1m (39.37 in.), 4mm2 / 12 AWG
Connector MC4
SHIPPING INFORMAT19U.
Container FT
Pallets
Panels
305 W
53'
Double stack
36
936
285.48 kW
40'
Double stack
28
728
222.04 kW
Panels
Weight
Height
Width Length
Pallet
26
1,105lbs
45.50"
45.50" 67.00"
Mission Solar Energy reserves the right to make specification changes without notice
CLASS LEADING 300-31OW
IEC
61215/61730/61701
UL
UL 1703 listed
Snus
PoWe.,Guord CEC
UmIll
MSE305SQ8T: 305WP, 60CELL SOLAR MODULE
CURRENT -VOLTAGE CURVE
12
Cells Temp.
10
a
N 6
c
0
U
a
2 -
0
Incident Irrd•=1,000 2 W/m
305.1 W
Incident Irrd.=800 2W/m
2• A W
Incident Irrd.=600 2W/m
!. 1. W
Incident Irrd.=400 zW/m 123 L
Incident Irrd.=200 'W/m 5' VY
t
0
20 30 20
Voltage [V]
Current -voltage characteristics with dependence on irradiance
and module temperature
BASIC DESIGN (UNITS: mm)
-
3�:A
z� - irlili )J 11I 1111 1
Front View
�e 50
_ I
35.00
I 'F
' --Drain
-� Hole �I 297.00
, ! I .
1-�
77.00
832.00 ' f
! Mo- unting Hole
I,
I
ii
-)---Y, Grounding
Hole
eaz oo II'
4-
I�, 1
,000 _�-
I
Back View
1
MISSION SOLAR
ENERGY sue' <
Mission Solar Energy 18303 S. New Braunfels Ave., San Antonio, Texas 78235
info@missionsolar.com I www.missionsolar.com
"A& IRONRIDGE Integrated Grounding System Installation Overview
Simplified Grounding
Fnr (',rPatPr RnfPty R I rnn/ar (r),zt
Traditionally, solar modules are grounded by attaching
lugs, bolts or clips to the module frame, then connecting
these to a copper conductor that runs throughout the
array. This process adds time and cost to the installation,
and often results in improper grounding, creating
significant long-term safety risks.
The IronRidge Integrated Grounding System solves these
challenges by bonding modules directly to the mounting
rails. This approach eliminates separate module
grounding hardware, and it creates many parallel
grounding paths throughout the array, providing
greater safety for system owners.
londing Strap
onding Straps are used to
)nd rail -to -rail connections.
hey are only required on the
til with the grounding lug.
#' Grounding Mid Clamp
Each Grounding Mid Clamp pierces through the
anodized coatings of both the module frame and
the mounting rail to form secure electrical bonds,
which are repeated throughout the array
Grounding Lug
A single Grounding Lug
connects an entire row
of PV modules to the
grounding conductor.
Install Roof Attachments
• Install appropriate roof flashing and/or standoff for roof type
• Attach L-Feet to flashing or standoff.
Prepare Rail Connections
• Insert splice into first rail, then secure with Bonding Strap and
self -drilling screw.
• Slide second rail over splice, then secure with opposite end of
Grounding Strap and self -drilling screw.
0 Mount & Ground Rails
• Attach rails to L-Feet and level rails.
• Install one Grounding Lug per row of modules.
• Connect Grounding Lug to grounding conductor
Install Modules & Clamps
• Install first module using End Clamps and Grounding Mid Clamps.
• Install additional modules using Grounding Mid Clamps.
• Finish row with a second pair of End Clamps.
Testing & Certification
The IronRidge Integrated Grounding
System has been tested and certified to
UL 2703 by Intertek Group plc.
UL 2703 is a proposed UL standard
for evaluating solar module mounting
and clamping devices. It ensures these
devices will maintain strong electrical and
mechanical connections over an extended
period of time in extreme outdoor
environments.
The testing process closely mirrors that
of UL 1703, the solar module testing
standard, including temperature and
humidity cycling, electrical and mechanical
load testing, and manufacturing quality
reviews.
Module Frame Compatibility
Dimension Range
A 31.Omm - 51.Omm
A B 5.08mm (minimum)
Any module frames whose parameters are not listed in the
provided table have not been tested for compatibility.
The Grounding Mid Clamp has proven robust in grounding solar
modules with a box frame construction, a range of anodization
thicknesses and nominal lengths of 78.5' or less.
All solar modules listed to UL 1703 and with frame construction
within the parameters stated above are compatible with the
IronRidge Integrated Grounding System.
Go to ironridge.com/ig
Jilt ngattr. rvwrr.ironrtd WCJA t-aw:227-W3 for more tnfor 1pnwai.... - /-,! � f is,
Manual
.,'.lt I RON RI DGE
Installation
Once the end module is set into position, place second
module into position, leaving a 1/2" gap between it and
the previous module. While holding module in place, drop
Grounding Mid Clamps into rail slots and rotate nuts to
engage T-bolts.
Slide second module flush against clamp tabs. Once
clamp teeth are in contact with both module frames and
the bolts are properly aligned in slots, torque to 84 in-Ibs
(55 in-Ibs for SunPower modules). Repeat procedure for
each following module.
► Make sure indent at top of T bolt is perpendicular to rail slot to
ensure T bolts are properly seated.
► If grounding mid clamps need to be reinstalled, slightly move the
modules so that clamp teeth are in contact with a new section of
the module frame.
Markings
Markings are located on the top surface of the Grounding
Mid Clamp and being with the manufacturing and model
number followed by the revision and manufacturing date.
Manufacturer and model number: IR
Revision and manufacturing date:
First digit (revision code): A = Rev A, B = Rev B, etc.
Second digit (month produced): A = Jan, B = Feb, etc.
Third & fourth digits (year produced): 15 = 2015, etc.
Ratings
Max Overcurrent Protective Device (OCPD) Rating: 25A
Installer is responsible for and shall provide an appropriate
method of direct -to -earth grounding according to the latest
edition of the National Electrical Code, including NEC 250:
Grounding and Bonding, and NEC 690: Solar Photovoltaic
Systems.
If loose components, loose fasteners or corrosion
are found during periodic inspection, replace affected
components immediately.
Grounding Mid Clamp
Leave � 1. Drop in Clamps
ap Between Parallel to Rail
Modules -
„r.
2. Rotate Nuts
to Engage Bolts
Place Second Module
into Position
in Rail Slot
Torque to 84 in-Ibs
(55 in-n-Ibsbs for
SunPower modules)
- --------_--
T-Bolt Indent
Perpendicular
to Rail
i
IR AA01
0
7OPS = ErLtx
Module Compatibility
The Grounding Mid Clamp may be used to ground and/or mount a PV module complying with UL 1703 only when the
specific module has been evaluated for grounding and/or mounting in compliance with the included instructions. Unless
otherwise noted, "xxx" refers to the module power rating and both black and silver frames are included in the certification.
AstroEnergy Solar
Modules with 35, 40, and 45mm frames and model identifier aaSM66yyPzz-xxx; where "aa" can be CH or A; "yy' can be either 10 or
"zz"
12; can be blank or (BL).
Modules with 40mm frames and model identififer CS6Y-xxxZ; where "Y" can be K, P, V, or X; and ""Z"" can be M, P, PX, or P-SD.
Modules with 35, 40, and 50mm frames and model identifier ET-Y6ZZxxxAA; where "Y" can be P, L, or M; "ZZ" can be 60 or 72; and
Canadian Solar
ET Solar
"AA" can be WB, WW, BB, WBG, WWG, WBAC, WBCO, WWCO, WWBCO or BBAC.
GigaWatt Solar
Modules with 40mm frames and model identifier GWxxxYY; where "YY" can be either PB or MB.
Modules with 40, 45, and 50mm frames and model identifier HSLaaP6-YY-1-xxxZ; where "aa" can be either 60 or 72; "YY" can be
Hanwha Solar
PA or PB; and "Z" can be blank or B.
Hanwha O CELLS
Modules with 32, 35, 40, and 42mm frames and model identifier O.YY-ZZ-xxx; where "YY" can be PLUS, PRO, or PEAK; and "ZZ"
can be G3, G4, L-G2, L-G3y, L-G4y, BFR-G3, BLK-G3, BFR-G4, BFR-G4.1, or G4.1/SC.
Hyundai
Modules with 35 and 50mm frames and model identifier HiS-YxxxZZ; where "Y" can be M or S; and "ZZ" can be MI, MF, MG, SG,
Rl, RG, TI, or TG.
Modules with 40 and 45mm frames and model identifier JAyyzz-bb-xxx/aa; where "yy' can be M6 or P6; "zz" can be blank, (K), (L),
JA Solar
(R), (V), (BK), (FA), (TG), (FA)(R), (L)(BK), (L)(TG), (R)(BK), (R)(TG), (V)(BK), (BK)(TG), or (L)(BK)(TG); "bb" can be 48, 60, or 72;
and "aa" can be MP, SI, PR, 386, 4BB, 4BB/RE.
Jinko
Modules with 35 and 40mm frames and model identifier JKMYxxxZZ; where Y' can either be blank or S; and "ZZ" can be M, P, PP,
P-B, or P-V.
Modules with 46mm frames and model identifier KYxxxZZ-AA; where "Y" can be D or U; "ZZ" can be blank, GX, or SX; and "AA"
Kyocera
can be LPU, LFU, UPU, LIPS, LPB, ,LFB, LFBS, LF132, LP62, 3AC, 313C, 3FC, 4AC, 413C, 4FC, 4UC, 5AC, 5131C, 5FC, 5UC, 6BC,
6FC, or 813C.
LG
Modules with 35, 40, and 46mm frames and model identifier LGxxxyl z-bb; where "y" can be A, N, or S; "z" can be C or K; and "bb"
can be A3, 133, G3, C4 or K4.
Mistubishi
Modules with 46mm frames and model identifier PV-MYYxxxZZ; where "YY" can be LE or JE; and "ZZ" can be either HD, HD2, or
FB.
Motech
IM and XS series modules with 40, 45, and 50mm frames.
Panasonic
Modules with 35mm frames and model identifier VBHNxxxSAyy; where "yy" can be either 06, 068, 11, 11 B, 15, 156, 16 or 1613.
Phono Solar
REC Solar
Renesola
SolarWorld
Stion
SunEdison
Suniva
Sunpower
RECOGNIZED
COMPONENT Suntech
Trina
�i�)Us
Winaico
Intertek
4008083 Yingli
Modules with 35, 40, and 45mm frames and model identifier PSxxxY-ZZ/A; where "Y" can be M or P; "ZZ" can be 20 or 24; and "A"
can beF,TorU.
Modules with 38 and 45mm frames and model identifier RECxxxYYZZ; where "YY" can be M, PE or TP; and "ZZ" can be blank,
BLK, SLV, or 72.
Modules with 35, 40 and 50mm frames and model identifier JCxxxY-ZZ; where "Y" can be F, M or S; and "ZZ" can be Ab, Ab-b, Abh,
Abh-b, Abv, Abv-b, Bb, Bb-b, Bbh, Bbh-b, Bbv, Bbv-b, Db, or Db-b.
Sunmodule Plus, Protect or XL mono or poly modules with 31, 33 or 46mm frames and model identifier SW-xxx.
Thin film modules with 35mm frames and model identifier STO-xxx.
Modules with 35, 40, and 50mm frames and model identifier SE-YxxxZABCDE; where "Y" can be B, F, H, P, R, or Z; "Z" can be 0 or
4; "A" can be B, C, D, E, H, I, J, K, L, M, or N; "B" can be B or W; "C" can be A or C; "D" can be 3, 7, 8, or 9; and "E" can be 0, 1 or
2.
Modules with 35, 38, 40, 46, and 50mm frames and model identifiers OPTxxx-AA-B-YYY-Z or MVXxxx-AA-B-YYY-Z; where "AA" is
either 60 or 72; "B" is either 4 or 5; "YYY" is either 100,101,700,1BO, or 161; and "Z" is blank or B.
SPR-A-xx series with standard (G3) or InvisiMount (G5) 46mm frames; where "A" is either E or X; and "xx" is the series number
Vd, Vem, Wdb, Woe, and Wd series modules with 35, 40, and 50mm frames.
Modules with 35, 40 and 46mm frames and model identifier TSM-xxxYYZZ; where "YY" can be PA05, PC05, PD05, PA14, P014, or
PD14; and "ZZ" can be blank or A or A.05 or A.08.
Modules with 35 and 40mm frames and model identifier Wsy-xxxz6; where "y" can be either P or T; and ""z"" can be either M or P.
Panda, YGE, and YGE-U series modules with 35, 40, and 50 mm frames.
�= 0 2015 IronFtidge, Inc- All nghls t**&v@'d. ► on wwwurwwidge.com or call 1-40W 7-9 z I- rnara fMorpn+filon. Vee�Qn t.�7
AUTHORIZATION TO MARK
This authorizes the application of the Certification Mark(s) shown below to the models described in the Product(s)
Covered section when made in accordance with the conditions set forth in the Certification Agreement and Listing
Report. This authorization also applies to multiple listee model(s) identified on the correlation page of the Listing
Report.
This document is the property of Intertek Testing Services and is not transferable. The certification mark(s) may be
applied only at the location of the Party Authorized To Apply Mark.
Applicant: IronRidge, Inc
Address:
1495 Zephyr Ave
Hayward, CA 94544
Country:
USA
Contact:
Yann Schwarz
Phone:
(800) 227-9523
FAX:
(707) 459-1833
Email:
yschwarz@ironridge.com
Party Authorized To Apply Mark: Same as Manufacturer
Report Issuing Office: Lake Forest, CA
Control Number: 4008083 Authorized by:
Manufacturer: Precision Die & Stamping, Inc
Address:
1704 W. 10th Street
Tempe, AZ 85281
Country:
USA
Contact:
Andy Frola
Phone:
(480) 967-2038
FAX:
(480) 829-0838
Email:
andy@precisiondie.com
z�l kAVI
for Thomas J. Patterson, Certification Manager
Intertek
This document supersedes all previous Authorizations to Mark for the noted Report Number
This Authorization to Mark is for the exclusive use of Intertek's Client and is provided pursuant to the Certification agreement between Intertek and its Client. Intertek's responsibility and liability are
limited to the terms and conditions of the agreement. Intertek assumes no liability to any parry, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned
by the use of this Authorization to Mark. Only the Client is authorized to permit copying or distribution of this Authorization to Mark and then only in its entirety Use of Intertek's Certification mark is
restricted to the conditions laid out in the agreement and in this Authorization to Mark. Any further use of the Intertek name for the sale or advertisement of the tested material, product or service must
first be approved in writing by Intertek. Initial Factory Assessments and Follow up Services are for the purpose of assuring appropriate usage of the Certification mark in accordance with the
agreement, they are not for the purposes of production quality control and do not relieve the Client of their obligations in this respect.
Intertek Testing Services NA Inc.
545 East Algonquin Road, Arlington Heights, IL 60005
Telephone 800-345-3851 or 847-439-5667 Fax 312-283-1672
Standard(s): UL Subject 2703 Outline of Investigation for Rack Mounting Systems and Clamping Devices for Flat -Plate
Photovoltaic Modules and Panels, Issue Number: 1, October 4, 2010
Product: XR Rails with Integrated Grounding.
Brand Name: IronRidge Roof Mount
Models: IR XR followed by 4 Alphanumeric Characters
ATM for Report 101541132LAX-002 Page 2 of 2 ATM Issued: 28-Jan-2016
ED 16.3.15 (1-Jan-13) Mandatory
IRONRIDGE
olar Is Not Always Sunny
Over their lifetime, solar panels experience countless
extreme weather events. Not just the worst storms in years,
but the worst storms in 40 years. High winds capable of
ripping panels from a roof, and snowfalls weighing
enough to buckle a panel frame. J11i
XR Rails are the structural backbone preventing
these results. They resist uplift, protect
against buckling and safely and efficiently
transfer loads into the building structure.
Their superior spanning capability
requires fewer roof attachments,
reducing the number of roof
penetrations and the amount
of installation time.
Force -Stabilizing Curve
Sloped roofs generate both vertical and lateral
forces on mounting rails which can cause them
to bend and twist. The curved shape of XR Rails
is specially designed to increase strength in both
directions while resisting the twisting. This unique
feature ensures greater security during extreme
weather and a longer system lifetime.
to
XR Rail Family
Compatible with Flat & Pitched Roofs Corrosion -Resistant Materials
XR Rails are IronRidge offers All XR Rails are made of marine -grade
A compatible with 52Va range of tilt leg aluminum alloy, then protected with an
FlashFoot and options for flat anodized finish. Anodizing prevents surface
other pitched roof roof mounting and structural corrosion, while also providing sh-10-
attachments. applications. a more attractive appearance.
CLASSIFICATION
Constructional Data Report (CDR)
11.0 Reference and Address
Report Number 101541132LAX-002 Original 22-May-2014 Revised: 15-Jan-2016
Standard(s) UL Subject 2703 Outline of Investigation for Rack Mounting Systems and Clamping Devices
for Flat -Plate Photovoltaic Modules and Panels, Issue Number: 1, October 4, 2010
Applicant IronRidge, Inc
Address
1495 Zephyr Ave
Hayward, CA 94544
Country
USA
Contact
Yann Schwarz
Phone
(800) 227-9523
(510)225-0973
FAX
(707) 459-1833
Email
vschwarzedi iron rid ile.com
Manufacturer 2 Precision Die & Stamping, Inc.
1704 W. 10th Street
Address
Tempe, AZ 85281
Country
USA
Contact
Andy Frola
Phone
(480) 967-2038
FAX
(480) 829-0838
Email
andW,:'( recisiondie.com
Manufacturer 1 IronRidge, Inc.
Address
1495 Zephyr Ave
Hayward, CA 94544
Country
USA
Contact
Jim Norsworthy Or
Dave Taggart
Phone
(707) 363-3025
(800) 227-9523
FAX
(510) 225-0975
Email
inorsworthv( ironridce.com
dtaaaart&..ironridae.com
Page 1 of 86
This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. intertek's responsibility aril
liability are limited to the terms and conditions of the agreement. Intertek assures no liability to any party, otter than to the Client in accordance with the
agreement. for any loss, expense or damage occasioned by the use of this report. Only the Client is aulhofized to permit copying or distribution of this report and
then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be
approved in writing by Intertek_ The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the
material, product, or service is or has ever been under an Intertek certification program.
Report No. 101541132LAX-002 Page 2 of 86 Issued: 22-May-2014
IronRidge, Inc. Revised: 15-Jan-2016
2.0 Product Description
Product XR Rails with Integrated Grounding.
Brand name IronRidge Roof Mount
The product covered by this report is the IronRidge Rails with Integrated Grounding solar roof
mounting system. This system is designed to provide bonding and grounding to photovoltaic
modules. The mounting system employs anodized aluminum rails that are roof mounted using
aluminum Extruded L Foot brackets. The mounting rails in this report are XRL, XR10, XR100
and XR1000 Rail. All rails have an optional aluminum splice which ties the rails together to
extend their length.
A grounding strap and stainless steel hardware are required for penetrating the anodized
coating of the rails, creating a bonded connection from rail to rail. 304 stainless steel Grounding
Mid Clamp and aluminum End Clamps are used to attach and support framed photovoltaic
modules to the system. The End Clamps are not used as a grounding means.
The Grounding Mid Clamps are installed onto the module frame by using a 18-8 stainless steel
serrated T-Bolt and a 18-8 stainless steel Flange Hex Nut that gets screwed onto the rails to a
Description specified torque. The retention teeth of the clamp and bolt penetrate the anodized coating of
the photovoltaic modules frame and rail to contact the metal, creating a bonded connection
from module to module and module to rail.
The grounding of the entire system is intended to be in accordance with the latest edition of the
National Electrical Code, including NEC 250: Grounding and Bonding, and NEC 690: Solar
Photovoltaic Systems. Any local electrical codes must be adhered in addition to the
national electrical codes. An entire array, regardless of size, is grounded via one grounding
lug. The WEEB Grounding Lug is secured to XRL, XR10, XR100 or XR1000 Rail's top slot
using stainless steel hex bolt or T-Bolt, flat washer, split lock washer, and nut, tightened to
manufacture's specified torque. The WEEB Grounding Lug is intended for use with one solid or
stranded copper wire, conductor size 14 AWG though 6 AWG. The Titan Grounding Lug is
secured to XRL, XR10, XR100 or XR1000 Rail's side center cavity of rails using stainless steel
T-bolt, k-lock nut, star washer, and machine screw. The Titan Grounding Lug is intended for
use with one solid or stranded copper wire, conductor size 14 AWG though 4 AWG.
Models IR XR followed by 4 Alphanumeric Characters
Model Similarity N/A
Fuse Rating: 20 A
Fire Class Resistance Rating:
- Class A for Steep Slope Flush -Mount (Symmetrical) Applications when using Type 1,
Type 2 and Type 3, Listed Photovoltaic Module.
Ratings - Class A for Low Slope Flush -Mount (Symmetrical) Applications when using Type 1,
Type 2 and Type 3, Listed Photovoltaic Module.
- Class A for Steep Slope Tilt -Mount ( Asymmetrical) Applications when using Type 1
and Type 2, Listed Photovoltaic Module.
- Class A for Low Slope Tilt -Mount ( Asymmetrical) Applications when using Type 1,
Type 2 and Type 3, Listed Photovoltaic Module.
ED 16.3 15 (1-Jan-13) Mandatory
Report No. 101541132LAX-002
IronRidge, Inc.
2.0 Product Descri
Page 3 of 86
Issued: 22-May-2014
Revised: 15-Jan-2016
These systems were evaluated or tested for bonding ana grounamg wain the toliowing PV-
Module frames:
Motech - Black or Silver Frames
Models:
IM and XS series, 60 and 72 cell modules with 40 mm frame height.
IM and XS series, 60 and 72 cell modules with 45 mm frame height.
IM and XS series, 60 and 72 cell modules with 50 mm frame height.
Suntech - Black or Silver Frames
Models:
Wdb, Wde, and Wd series, 60 and 72 cell modules with 35 mm frame height.
Vd series, 60 and 72 cell modules with 50 mm frame height.
ET Solar - Black or Silver Frames
Models:
ET Solar 60 cell modules with 35 and 40 mm frames
ET-Y660xxxZZ
Where "Y" can be P, L, or M; "xxx" refers to the module power rating; "ZZ" can be WB, WW,
BB, WBAC, or BBAC
ET Solar 72 cell modules with 40 and 50 mm frames
ET-Y672xxxZZ
Where "Y" can be P, L, or M; "xxx" refers to the module power rating; "ZZ" can be WB, WW,
BB, or WBG
Hyundai - Black or Silver Frames
Models:
SG, MG, RG and TG Series, 60 cell modules with 35 mm frame height.
MI, RI and TI Series, 72 cell modules with 50 mm frame height.
Yingli - Black or Silver Frames
Models:
Panda and YGE models, 60 cell modules with 40 mm or 35 mm frame height.
YGE models, 72 cell modules with 50 mm or 40 mm frame height.
Kyocera -
Models:
KD(xxx)GX-LPU, KD(xxx)GX-LFU, KD135SX-UPU, KD(xxx)GX-LFBS, KD(xxx)GX-LPB
KD(xxx)GX-LFB, KD(xxx)GX-LFB2, KD(xxx)GX-LPB2
KD135GX-LPS, KD140GX-LPS, KD140SX-UPU
KU(xxx)-3AC, KU(xxx)-4AC, KU(xxx)-5AC, KU(xxx)-3BC, KU(xxx)-4BC
KU(xxx)-5BC, KU(xxx)-6BC, KU(xxx)-8BC, KU(xxx)-3FC, KU(xxx)-4FC
KU(xxx)-5FC, KU(xxx)-6FC, KU(xxx)-4UC, KU(xxx)-5UC.
Where xxx refers to the module power rating
Canadian Solar - Black or Silver Frames
Models:
CS6P-M 60 Cell Modules with a 40mm frame height.
CS6P-P 60 Cell Modules with a 40mm frame height.
CS6X-M 72 cell modules with a 40mm frame height.
CS6X-P 72 cell modules with a 40mm frame height.
Report No. 101541132LAX-002
IronRidge, Inc.
2.0 Product
Other Ratings
Page 4 of 86
Issued: 22-May-2014
Revised: 15-Jan-2016
LG Modules - Black or Silver Frames
Models:
LG 60 cell modules with 35 mm frames:
LGxxxy1z-b3
Where xxx is the module power rating, "y" can be A,N or S, 'Y' can be C or K, and "b" can be
A, B, or G.
LG 60 cell Modules with 40mm frames:
LGxxxy1 z-G4
Where "xxx" is the module power rating, "y' can be N or S, and 'Y' can be C or K
LG 72 Cell Modules with 46mm frames:
LGxxxy2z-b3
Where "xxx" is the module power rating, "y" can be N or S, 'Y' can be C or K, and "b" can be A,
B, or G
Suniva Modules - Black or Silver Frames
Models:
60 Cell Modules with 35 and 40mm frames:
O PTxxx-60-A-YYY-Z
M VXxxx-60-A-YYY-Z
Where "xxx" is the module power rating, "A" is either 4 or 5, "YYY" is either 100,101,700,1 B0,
or 1131, and 'Y' is blank or B.
72 Cell Modules with 38, 46, and 50mm frames:
OPTxxx-72-A-YYY-Z
MVXxxx-72-A-YYY-Z
Where "xxx" is the module power rating, "A" is either 4 or 5, "YYY' is either 100,101,700,1 BO,
or 1131, and "Z" is either blank or B
Hanwha Modules - Black or Silver Frames
Models:
HSL72P6-PA-1-xxx(50mm frame)
HSL72P6-PB-1-xxx(45mm frame)
HSL60P6-PB-1-xxx(40mm frame)
HSL60P6-PA-1-xxx(45mm frame)
The model number can be followed with a "B"
Where xxx is the module power rating
Trina Solar Modules - Black or Silver Frames
Models:
TSM-xxxPA05 (35mm frame height)
TSM-xxxPC05 (35mm frame height)
TSM-xxx-PD05 (35mm frame height)
TSM-xxxPA05 (40mm frame height)
TSM-xxxPA14 (46mm frame height)
TSM-xxxPD14 (40mm frame height)
TSM-xxxPC14 (40mm frame height)
The model number can be followed by A and .05 or .08
Where xxx refers to module power rating
ED 16.3.15 (I-Jan-13) Mandatory
ED 16.3.15 (1-Jan-13) Mandatory
Report No. 101541132LAX-002 Page 5 of 86 Issued: 22-May-2014 Report No. 101541132LAX-002 Page 6 of 86 Issued: 22-May-2014
IronRidge, Inc. Revised: 15-Jan-2016 IronRidge, Inc. Revised: 15-Jan-2016
2.0 Product Description 2.0 Product Description
SolarWorld Modules - Black or Silver Frames
Models:
Sunmodule Plus SW-xxx,
Sunmodule Protect SW-xxx,
Sunmodule XL SW-xxx
Mono or Poly with 31, 33, or 46 mm frame height.
Where xxx refers to the module power rating
Phono Solar Modules - Black or Silver Frames
Models:
PSxxxP-20/U, PSxxxM-20/U, PSxxxP-24/T, PSxxxM-24/T with 40mm frame height
Where xxx refers to module power rating
SunEdison modules - Black or Silver Frames
Models:
SE-QxxxBCC-3Y, SE-MxxxBCC-3Y, SE-FxxxBCC-3Y, SE-PxxxBCC-3Y, SE-QxxxBMC-3Y
SE-MxxxBMC-3Y, SE-FxxxBMC-3Y, SE-DxxxBMC-3Y, SE-PxxxBMC-3Y with 50mm frame
height.
Where xxx refers to module power rating
Hanwha Q CELLS modules - Black or Silver Frames
Models:
Hanwha QCells 60 cell modules with 32 mm frames
Q. PL U S-G4-xxx
Q.PRO BFR-G4-xxx
where xxx refers to module power rating
Hanwha QCells 60 cell modules with 35 mm frames:
Q.PRO-G3-xxx
Q. PRO-BFR-G3-xxx
Q.PEAK BLK G3-xxx
Q.PLUS G3-xxx
where xxx refers to module power rating
Hanwha QCells 72 cell modules with 35 mm frames:
Q.PRO L-G4y-xxx
Q.PLUS L-G4y-xxx
where "y" can be blank, 1 or 2 and "xxx" refers to module power rating
Hanwha QCell 72 cell modules with 40 mm frames:
Q.PRO L-G2xxx
Q.PRO L-G3y-xxx
where "y" can be blank or 1 and "xxx" refers to module power rating
Hanwha QCell 72 cell modules with 42 mm frames:
Q.PRO L-G2-xxx
where "xxx" refers to module power rating
Renesola Modules - Black or Silver Frames
Models: Mono and Virtus II Modules:
JCxxxM-24/Abh, JCxxxS-24/Abh, JCxxxF-24/Abh, JCxxxM-24/Abh-b, JCxxxS-24/Abh-b
JCxxxF-24/Abh-b, JCxxxM-24/Ab, JCxxxM-24/Abv, JCxxxS-24/Ab, JCxxxF-24/Ab
JCxxxM-24/Ab-b, JCxxxM-24/Abv-b, JCxxxS-24/Ab-b, JCxxxF-24/Ab-b with 50mm frame
height.
JCxxxM-24/Bb, JCxxxM-24/Bbv, JCxxxS-24/Bb, JCxxxF-24/Bb, JCxxxM-24/Bb-b
JCxxxM-24/Bbv-b, JCxxxS-24/Bb-b, JCxxxF-24/Bb-b, JCxxxM-24/Bbh, JCxxxS-24/Bbh
JCxxxF-24/Bbh, JCxxxM-24/Bbh-b, JCxxxS-24/Bbh-b, JCxxxF-24/Bbh-b with 40mm frame
height.
JCxxxS-24/Db, JCxxxF-24/Db, JCxxxS-24/Db-b, JCxxxF-24/Db-b with 35mm frame height.
Where xxx refers to the module power rating.
Sunpower Modules- Black or Silver Frames
Models:
SPR-E-xx series with standard (G3) or InvisiMount (G5) 46 mm frame
SPR-X-xx series with standard (G3) or InvisiMount (G5) 46 mm frame.
where xx is the series number
Panasonic Modules - Black or Sliver Frames
Models:
VBHNxxxSA06, VBHNxxxSA06B, VBHNxxxSA11, VBHNxxxSA11 B with 35 mm frame height.
Where xxx refers to the module power rating
Winaico Modules - Black or Silver Frames
Models:
Winaico 60 Cell modules with 35 and 40 mm frames
W sy-xxxz6
Where "y" can be either P or T, "xxx" is the module power rating, and 'Y' can be either M or P
Mitsubishi Modules - Black or Silver Frames
Models:
PV-MYYxxxzz
Where YY can be LE or JE, xxx is the module power rating, and ZZ can be either HD, HD2, or
FB
Jinko Solar Modules - Silver Frames
Models:
JKMxxxP-60: Where xxx is the module power rating between 250-270 in increments of 5.
JKMSxxxP: Where xxx is the module power rating between 255-270 in increments of 5.
JKMxxxPP-60: Where xxx is the module power rating between 255-270 in increments of 5.
ED 16.3,15 (1-Jan-13) Mandatory
ED 16.3.15 (1-Jan-13) Mandatory
8431 Murphy Drive
Middleton, WI 53562 USA
Telephone: 608.836.4400
Facsimile: 608.831.9279tek www.inter-com
Test Verification of Conformity
sm_
Starling Madison Lafquist, Inc,
r
r.
5224 South 3r Street, Phoenix, Anixona 85040
tel: (602) 438-2500 fox: (602) 438-2505 ROC#E291316 www.smleng.cam
IronRidge February 15, 2019
In the basis of the tests undertaken, the sample(s) of the below product have been found to comply with the requirements of
28357 Industrial Boulevard Page 1 of 21
the referenced specifications at the
time the tests were carried out.
Hayward, CA 94545
iApplicant Name & Address:
IronRidge, Inc. 1,
Attu: Mr, Carey Geiger, Vice President New Markets
1495 Zephyr Ave.
Hayward, CA 94544
Subject: IronRidge XRt(lili Rail, Roof Flush Mounting System — Structural Analysis
USA
Product Description:
XR Rails with Integrated Grounding.
Dear Sir:
Ratings & Principle
Fire Class Resistance Rating:
We have analyzed the IronRidge XRHHI Rail for the subject solar module support system and
Characteristics:
-Flush Mount (Symmetrical). Class A Fire Rated for Low Slope applications when using Type 1, 2
determined (bat, for the configurations and criteria dcseribed below, it is in compliance with the
and 3, listed photovoltaic modules. Class A Fire Rated for Steep Slope applications with Type1,
applicable sections of the following Reference Documents_
2 and 3, listed photovoltaic modules. Tested with a 5" gap (distance between the bottom the
module frame and the roof covering), per the standard this system can be installed at any gap
allowed by the manufacturers installation instructions. No perimeter guarding is required.
Codes: ASCUSEI 7-10 Min. Design Loads for Buildings &Other Structures
International F3ttild.illtg Code 2012 Edition
Models:
51-61GD-005, 51-61GD-005B, 51-5000-001 and 51-65-001
Other: AC428, Acceptance Criteria for Modular Framing Systems Used to Support PV
Brand Name:
IronRidge Roof Mount
Modules, dated Effective November 1, 2012 by ]CC -ES
Relevant Standards:
UL 2703 (Section 15.2 and 15.3) Standard for Safety Mounting Systems, Mounting Devices,
Aluminum Design I%IanuaL 2010 Edition
Clamping/Retention Devices, and Ground Lugs for Use with Flat -Plate Photovoltaic Modules
and Panels, First Edition dated Jan. 28, 2015 Referencing UL1703 Third Edition dated Nov. 18,
The IronRidge XRl00 Rail is an extruded aluminum section with an overall depth of 2.438 in, and a
2014, (Section 31.2) Standard for Safety for Flat -Plate Photovoltaic Modules and Panels.
net area of il.583 sq.in. The rails are used to support solar modules, typically, on the roof of a
Verification Issuing Office:
Intertek Testing Services NA, Inc.
building. See Exhibit 0011— attached_ The modules are clamped to the rails by the IronRidge
8431 Murphy Drive
Module 'Mounting Clamps, as shown in the attached Exhibit, The rails are attached to aluminum
Middleton, WI 53562
angle brackets that are either attached directly to the roof framing or attached to a stand that is
Date of Tests:
08/27/2014 to 03/17/2015
screwed to the roof framing- The rails are mounded across the slope with a small clearance (flush
Test Report Number(s):
101769343MID-OOlr1, 101769343MID-001a,101915978MID-001 & 101999492MID-001arl-crl.
mounting) to the tuiderlying roof Structure. The installed solar modules are at the Same Slope as the
This verification is part of the full test report(s) and should be read in conjunction with them. This report does not automatically
underlying roof structure.
imply product certification.
Completed by: Chad Naggs
Reviewed by: GregoryAllen
All loads are transferred to the roof framing through the angle brackets by simple bi-axial flexure of
Title: Technician II, Fire Resistance Title: Engineering Team Lead, Fire Resistance
the rails. The maximum span of the rails is governed by either the mid -span flexural strmes or the
deflection requirement that the rail not come into contact with the roof.
Signature:
Signature:]
Date: 03/30/2015
Date: 03/30/2015
The effect of seismic loads (for all design categories A-F) have been determined to be less than the
efTect due to wind leads in all load conditions and combinations, Therefore, the maximum allowable
spans for common load cases are shown in the tables below. Tables 1 A-9A are for modules with a
'cables
maximum lung distension of 67.5 inches and I B-9B are for modules with a maximum tang
— _
-
dimension of 78.5 inches.
This Verification is for the exclusive use of lntertek's client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are
limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client m accordance with the agreement, for any loss, expense
or damage occasioned by the use of this Verification. Only the Client is authorized to permit copying or distribution of this Verification. Any use of the Intertek name or one of its Starling Nladison Lofquist, Inc. Consulting Structural and Forensic Engineers
marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test/inspection results Texas Firm Registration #F-16420
referenced in this Verification are relevant only to the sample tested/inspected. This Verification by itself does not imply that the material, product, or service is or has ever been
under on Intertek certification program.
GFT-OP-13a (24-MAR-2014)
' r
IronRidge
Mr, Carey Geiger
IronRidge YR100 Rail, Roof 1=htsh Mounting System — Stnlctural Analysis
Modulo Glass fCe'lls
Frorne Coirnpsiitiiity,
X - I.2. 2.2 myrt
'f=15.40mm
i' -x
February 15, 200
Page 21 of 21
Figure 8: CAN-10 [`.lamp Module Frame f)imcnsional Requirements
Our analysis assumes that the rail;, including the connections and associated hardware., am installed
in a workmanlike manner in accordance v6th the IrorlRidge Flush Mount Trt.Stallation Manual" by
lronRldge and gcncrally accepted standarrls of construction practice. Additional information is
a vailable It the IronRidge web site:, IronRidge,conl. 4ferjlication of PV Module capacity to support
the loads associated with the given array shall be lihe responsibility of the Contractor of Owner and
not lronitiJgc or Starling Madison Lofquist.
The adequacy of the supporting, roof framing is to be determined by others.
Please feel line to Contact tile at your convenience if you have any questions,,
Respectfully yours,
Tres Warner, P,tr, • '•.*�
Design Division Manager h.................
TREE J. WARNER
Digitally signicd tsyTrt;3
I Warner
Trey DN: c-US omStarling
Madison Lofqulst Inc,
0
u=A014z73w00153
B F918), Cn rrn -Tres JNarner Date. 2w 9.02.- 9
1429:07-47'O6'
Starling Madison Lofquisy Inc, Cc►r,sulting SuUCLUtal and Forensic Engitrcers
Texas Firm Registrsttion 4117-16420
AUTHORIZATION TO MARK
This authorizes the application of the Certification Mark(s) shown below to the models described in the Product(s)
Covered section when made in accordance with the conditions set forth in the Certification Agreement and Listing
Report. This authorization also applies to multiple listee model(s) identified on the correlation page of the Listing
Report.
This document is the property of Intertek Testing Services and is not transferable. The certification mark(s) may be
applied only at the location of the Party Authorized To Apply Mark.
Applicant: IronRidge, Inc
1495 Zephyr Ave
Address:
Hayward, CA 94544
Country:
USA
Contact:
Yann Schwarz
Phone:
(800)227-9523
FAX:
(707) 459-1833
Email:
yschwarz@ironridge.com
Party Authorized To Apply Mark: Same as Manufacturer
Report Issuing Office: Lake Forest, CA
Control Number: 4008377
Authorized by:
Manufacturer: IronRidge, Inc
Address:
1495 Zephyr Ave
Hayward, CA 94544
Country:
USA
Contact:
Jim Norsworthy Or
Phone:
(707)363-3025
FAX:
(510)225-0975
Email:
jorsworthy@ironridge.com
IT
for Thomas J. Patterson, Certification Manager
Intertek
This document supersedes all previous Authorizations to Mark for the noted Report Number
This Authorization to Mark is for the exclusive use of Intertek's Client and Is provided pursuant to the Certification agreement between Intertek and its Client. Intertek's responsibility and liability are
limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement. for any loss, expense or damage occasioned
by the use of this Authorization to Mark. Only the Client is authorized to permit copying or distribution of this Authorization to Mark and then only in its entirety. Use of Intertek's Certification mark is
restricted to the conditions laid out in the agreement and in this Authorization to Mark. Any further use of the Intertek name for the sale or advertisement of the tested material, product or service must
first be approved in writing by Intertek. Initial Factory Assessments and Fallow up Services are for the purpose of assuring appropriate usage of the Certification mark in accordance with the
agreement, they are not for the purposes of production quality control and do not relieve the Client of their obligations in this respect.
Intertek Testing Services NA Inc.
545 East Algonquin Road, Arlington Heights, IL 60005
Telephone 800-345-3851 or 847-439-5667 Fax 312-283-1672
Standard(s): UL Subject 2703 Outline of Investigation for Rack Mounting Systems and Clamping Devices for Flat -Plate
Photovoltaic Modules and Panels, Issue Number: 1, October 4, 2010
Product: XR Rails with Integrated Grounding.
Brand Name: IronRidge Roof Mount
Models: IR XR followed by 4 Alphanumeric Characters
ATM for Report 101541132LAX-002 Page 1 of 2
ATM Issued: 28-Jan-2016
ED 16.3.15 (1-Jan-13) Mandatory
June 20, 2014
Mr. Meir Adest
SolarEdge Technologies Ltd
6 Ha'Harash St.
HOD HASHARON, ISRAEL
3933 US Route 11
Cortland, NY 13045
Telephone: (607) 753-6711
Facsimile: (607) 756-9891
www.intertek.com
Letter Report No. 101703554CRT-001
Project No. G 10 1703554
Ph: +972.9.957.6620
email: meir.a@solaredge.com
Subject: ETL Evaluation of SolarEdge Products to NEC Rapid Shutdown Requirements
Dear Mr. Meir Adest,
This letter represents the testing results of the below listed products to the requirements contained in the following
standards:
National Electric Code, 2014, Section 690.12 requirement for rapid shutdown.
This investigation was authorized by signed Quote 500534459 dated 06/10/2014. Rapid shutdown test were
perform at SolarEdge Technologies Ltd, 6 Ha'Harash St HOD HASHARON, ISRAEL and witness by Intertek
personal on 06/17/2014.
The evaluation covers installations consisting of optimizers and inverters with part numbers listed below.
The testing done has verified that controlled conductors are limited to not more than 30 volts and 240 volt-
amperes within 10 seconds of rapid shutdown initiation.
Applicable products:
0 Power optimizers:
o PBxxx-yyy-zzzz; where xxx is any number, 0-9, up to a maximum value where xxx = 350; yyy
could be AOB or TFI; and zzzz is any combination of four letters and numbers.
o OP-XXX-LV, OP-XXX-MV, OP-XXX-IV, OP-XXX-EV; where xxx is any number, 0-9.
o Paaa, Pbbb, Pccc, Pddd, Peee; where aaa, bbb, ccc, ddd, eee is any number, 0-9 to a maximum
upto aaa=300, bbb=350 ccc=500, ddd=600, eee=700.
o Pxxx, Pyyy, Pzzz, Pmmm, Pnnn and P000; where xxx, yyy, zzz is any number, 0-9 to a maximum
up to xxx=300, yyy=350, zzz=500; where mmm, nnn, 000 is any number, 0-9 to a maximum up to
mmm=405, nnn=300, 000=350
• 1-ph Inverters:
o SE3000A-US / SE380OA-US / SE5000A-US / SE6000A-US / SE760OA-US / SE1000OA-US /
SE1140OA-US when the SolarEdge rapid shutdown cable labeled "MCI-CB-xxxxx-x" which is part
of kit SE1000-RSD-xx is installed in the inverter Safety Switch where xxxxx-xx is any number;
inverter part number may be followed by a suffix
Pagel of 2
This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms
and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use
of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or
advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only the sample tested. This
report by itself does not imply that the material, product or service is or has ever been under an Intertek certification program.
FJ f Wi
Appiwed
Intertek Intertek intertek Irztei tek Intertek Intertek
Intertek Testing Services NA, Inc.
SD 12.12 (11/11110) Informative
SolarEdge Technologies Ltd
• 3-ph Inverters:
Letter Report 101703554CRT-001
June 201h, 2014
o SE9KUS / SEIOKUS / SE20KUS when the SolarEdge rapid shutdown cable labeled "MCI-CB-xxxxx-
x" which is part of kit SE1000-RSD-xx is installed in the inverter Safety Switch where xxxxx-xx is
any number; inverter part number may be followed by a suffix
This letter report completes this portion of the evaluation covered by Intertek Project No.G101703554.
If there are any questions regarding the results contained in this report, or any of the other services offered by
Intertek, please do not hesitate to contact the undersigned.
Please note, this Letter Report does not represent authorization for the use of any Intertek certification marks.
Completed by:
Radhe Patel
Reviewed by:
Howard Liu
Title:
Signature:
Engineering Team Lead
-�----- 7^
Title:
Signature
StaffEngineer
Date
June 20m, 2014
Date:
June 20` , 2014
Intertek Testing Services NA, Inc.
Page 2 of 2
So 12.1.2 (11/11/10) Informative
- FA
STANDARD ECO
110 E. Houston St., CONTRACTOR SHALL CALL FOR
San Antonio, TX 78205 INSPECTIONS:
TX License #:32439 (817) 410-3010
VICINITY MAP
1�
f2600 Pool Road
SYSTEM INFORMATION
CONTRACTOR REGISTRATIC N ARIEL MAP
WILL BE REVOKED UPON
PERMIT EXPIRATION.
SCOPE OF WORK:
INTALL (36) ROOF MOUNTED PV SOLAR MODULES, (36) P320
POWER OPTIMIZERS,(1) SOLAREDGE 1000OH-US INVERTER
(240V), (1) 60A AC DISCONNECT, AND DERATE MAIN BREAKER TO
175A FROM 200A.
IBrittain Residence
2600 Pool Road Grapevine, TX 76051
JUL 19 2019 f a400 ra6l�.
ALL CHANGES REQUIRE
APPROVAL
OF REVISED PLANS
APPROVED s, ` n�; w e L BE.
KEPT ON JOBSITEATALL nMES
MO.`
N0
~1 h 0, 72
MY AM9M P'LANI TO BE KEPI ON
TM M SITE AT ALL TVAM
DATE: t 1 x BY:
BURDM INSPECTION .
RELEASE OM NOT APPLY TO N IN
EASEMENTS OR PUBLIC RIGHT-OF-WAY.
ALL CHANGES MUST BE APPROVED
SHEET INDEX.
-00- COVER SHEET AND PLOT MAP
-1- SITE PLAN DRAWING
-2- RACKING PLAN
-3- ELECTRICAL NOTES
-4- SINGLE LINE DIAGRAM
-5 ARRAY MAP SEPARATE PLUMBING, MECHANICAL,
-5.1- THREE LINE DIAGRAM EL.ECTRICAL.AND SIGN PERMITS
-6- PLACARDS SHALL BE REQUIRED
- - REFERENCE PAGE
- ATTACHED SPEC. SHEETS / ETC. -
-- INVERTER SPECIFICATIONS
-- MODULE SPECIFICATIONS
GENERAL NOTES
1. ALL CONSTRUCTION / INSTALLATION SHALL COMPLY WITH:
2017 NATIONAL ELECTRIC CODE (NEC)
2012 INTERNATIONAL FIRE CODE (IFC)
2012 INTERNATIONAL BUILDING CODE
2012 INTERNATIONAL RESIDENTIAL CODE
2012 INTERNATIONAL MECHANICAL CODE
2012 INTERNATIONAL PLUMBING CODE
2012 INTERNATIONAL EXISTING BUILDING CODE
2012 INTERNATIONAL FUEL GAS CODE
2012 INTERNATIONAL ENERGY CONSERVATION CODE
2. ALL DIMENSIONS WITHIN THESE PLANS ARE APPROXIMATE.
3. ALL CONDUITS ON ROOF SHALL BE A MINIMUM OF 1/2" OFF ROOF.
4. CONSTRUCTION LIMITS: ALL IMPROVEMENTS AND ACCESS SHALL
OCCUR WITHIN PLANT PROPERTY LINES.
5. PV EQUIPMENT SHALL BE INSTALLED IN ACCORDANCE WITH 2O17
NEC 690 & POSTED WITH APPLICABLE WARNINGS, SIGNAGE AND
PLAQUES PER 2017 NEC ARTICLE 705-10, 690-17, 690-64, AND 2012 IFC
SECTION 605.11.
6. ALL PV ARRAYS AND ASSOCIATED EQUIPMENT, CONDUIT AND
CONDUCTORS SHALL COMPLY WITH SECTION 605.11 OF THE 2012 IFC
FOR MARKING DC CONDUCTORS, LOCATION OF DC CONDUCTORS,
ROOF ACCESS, PATHWAYS AND SPACING. PLAN SHOULD SHOW
COMPLIANCE WITH THE IFC.
SYSTEM EQUIPMENT
(36x) MISSION SOLAR ENERGY MSE3IOSQ8T
(36x) POWER OPTIMIZERS P320
(Ix) SOLAREDGE SE 10000IWNTRACTOR COPY.
11.16 kW DC ISSUE., DRAWN BY: 00
10.00 kW AC 1 06/28/2019 1 ND
SITE PLAN
TYP ROOF ACCESS POINT
Y FIRE ACCESS PATHWAY
PROPOSED FLUSH MOUNTED SOLAR
MODULES AND POWER OPTIMIZERS
UTILITY METER
(OUTSIDE WALL)
NEW VISIBLE LOCKABLE UTILITY AC
DISCONNECT (CAPABLE OF BEING
LOCKED IN "OFF" POSITION)
IN
SCALE: 1" = 50'-0"
ELECTRICAL EQUIPMENT DETAIL
EXISTING
SERVICE PANEL _
(LOCATED
INSIDE)
D�Ewp,Y
\\K ------ ------ - — - ---------
EXISTING 200A PANEL
WITH A NEW 175A MAIN BREAKER
(INSIDE)
INVERTER MOUNTED
ON OUTSIDE WALL
UTILITY METER
CONSTRUCTION NOTES
O
1. SOLAR PHOTOVOLTAIC SYSTEM TO BE INSTALLED ON
RESIDENTIAL STRUCTURE.
W
O
2. THIS PROJECT HAS BEEN DESIGNED IN COMPLIANCE
4 N M
00
WITH THE CBC SECTION 1609 TO WITHSTAND A BASIC
N
WIND SPEED OF 110 MPH (3 SECOND GUST), WIND
M
EXPOSURE C.
3. THE HOUSE IS A ONE STORY STRUCTURE.
O U
4. THE ROOF MEMBERS ARE 2x4 RAFTERS ON 24"
W a
b
CENTERS. CONNECTION TO STRUCTURE SHALL NOT BE
WITHIN 6" OF NAILING PLATES.
O Q
po
_
5. THE SOLAR PHOTOVOLTAIC INSTALLATION SHALL NOT
O
OBSTRUCT ANY PLUMBING, MECHANICAL OR BUILDING
Q-
ROOF VENTS.
r^
6. ALL CONDUCTORS AND CONDUITS MOUNTED ON ROOF
SHALL BE MINIMUM 3 314" ABOVE ROOF SURFACE
(INCLUDING CABLES UNDERNEATH MODULES AND
RACKING).
COMPOSITION SHINGLE 7. ROOF ACCESS POINTS SHALL BE PROVIDED PER THE
ROOF STRUCTURE FOLLOWING (CRC R324.7.1, CBC 3111.4.1):
- LOCATED IN AREAS NOT REQUIRING PLACEMENT OF
GROUND LADDERS OVER OPENINGS SUCH AS DOORS
OR WINDOWS.
- LOCATED AT STRONG POINTS OF BUILDING
CONSTRUCTION IN LOCATIONS WHERE ACCESS POINT
DOES NOT CONFLICT WITH OVERHEAD OBSTRUCTIONS
SUCH AS: TREE LIMBS, WIRES, OR SIGNS
VISIBLE LOCKABLE UTILITY
AC DISCONNECT (CAPABLE
i OF BEING LOCKED IN "OFF"
POSITION)
NEW
Q � I1vV ��_SOLAREDGE
INVERTER
° (OUTSIDE WALL)
CITY OF GRAPEVINE
RELEASED FOR CONSTRUCTION
SHEET: _ 4'Z OF:
ES N
RELEASE .]DOT AUTHORIZE ANY WORK IN
OONFLICT WITH i HE BUILDING CODE OR ZONING OPMNANCE.
CITY APPF OVED PLANS TO BE KEPT ON
THE JOB SITE AT ALL TIMES
DATE: Z 2+ 20 BY:
BU LDING INSPECTION OMSION:
RELEASE DC IES NOT APPLY TO CONSTRUCTION
EASEMENTS OR PUBLIC RIGHT -OF --WAY.
ALL CHANGES MUST BE APPR[�v ,
* */ .... . ....... ......
J R. VI Cl i
. .12ES i,� 8 7 ...:...
t O l !��Oi
ZONAL
t6-28-2019
A
IIRUCTURALONLY
cslrucfural �in9ineers
Vincise.com
TSPC Finn Reg,.treL"n No F.206N
o
�l
U U N
~
N
O4
5
O V1
p _ W
PLO
CIO
REVISIONS:
DRAWN BY: ND
DATE: 06/28/2019
SITE PLAN
DRAWING
SHEET: 1
ENLARGED P.A RTT 4L ROOF/RACKING PLAN
9 I
i
6'-0"
33'-2"
, X
i • i
MISSION SOLAR
ENERGY MODULES
TYPICAL ATTACHMENT POINT W/ 5/16" S.S. LAG TO BE
CENTERED IN STRUCTURAL MEMBER. LAGS MUST
HAVE A MINIMUM OF 2.5" THREAD DEPTH INTO
STRUCTURAL BEAM
N
1800 SCALE: 1/8" = V-0"
RA CKING DETAIL
IRONRIDGE GROUNDING
MIDCLAMP
SUPPORT RAIL SPLICE AS REQ.
11'-0"
9'-11" r } -----r
I �
PV
MODULE
IRONRIDGE XR100
RAILING
L-FOOT
TYP. ATTACHMENT POINT
"QUICK MOUNT PV" SYST.
W/ 5/16" x 6" S.S. LAG. WITH
2 1/2" THREAD EMBEDMENT
INTO FRAME MEMBERS
Y FIRE ACCESS PATHWAY
2" x 4" RAFTERS CENTERLINE
16'-6"
INSTALLATION NOTES
O
1. DISTANCE BETWEEN PENETRATIONS NOT TO
u
EXCEED 6-0"
rT�
tn
w
p a,
2. RAIL OVERHANG FROM PENETRATIONS NOT TO
0"o
EXCEED 24"
m
3. LAG SCREWS SHALL BE AT LEAST 6" FROM ANY
o o
NAILING PLATES.
y
n�
4. LAGS MUST HAVE A MINIMUM OF 2.5" THREAD
p �
DEPTH INTO STRUCTURAL BEAM.
5. ADJUSTMENTS MAY BE REQUIRED DUE TO
r
EXISTING ROOF CONDITIONS.
v 1
6. THE COMBINATION OF MOUNTING SYSTEM AND
PV MODULES SHALL MEET THE MINIMUM
REQUIREMENTS TO ACHIEVE A CLASS "A" FIRE
RATING PER UL 1703 FIRE CLASSIFICATION
U
o
STANDARDS.
W
N
U U
7. PV EQUIPMENT SHALL BE INSTALLED IN
a 00
Q N
r,
ACCORDANCE WITH THE 2017 NATIONAL
ELECTRICAL CODE ARTICLE 690.
CONSTRUCTION MUST ADHERE FOR BOTH
Q
O
INSTALLATION OF ELECTRICAL WIRING AND
EQUIPMENT ASSOCIATED WITH THE SOLAR
C
PHOTOVOLTAIC SYSTEMS.
a
CITY 9F GRAPEVINE
RELEASED FOR CONSTRUCTION
SHEET: OF: 5 PtE .r ''
r
RELEASE DOES N T AUTHORIZE ANY WORK I(* ,3
CONFLICT WITH THE BUILDING CODE ORZ NIN ES R. VI ci
4
CITY APPROVED PLANS TO BE KEPT 1427
THE JOB ITE AT ALL TIMES �� ��ONAI.rr
6-28-2019
DATE: 2I� BY: R CTURAL ONLY
BUILDING INSPECTION DIVA ION:
RELEASE DOES NOI APPLY TO CONSTRUCTION IN
EASEMENTS OR PUBLIC RIGHT-OF-WAY.
ALL CHANGES MUST BE APPROVED
cSfrucfural �inyineers
vincise.com
TBPE Firm Regmi,alion No, F-20604
REVISIONS:
DRAWN BY: ND
DATE: 06/28/2019
RACKING PLAN
SHEET: 2
r0
PHOTOVOLTAIC TABLE MAXIMUM SYSTEM VOLTAGE V
BRITTAIN RESIDENCE OPERATING VOLTAGE FOR DC PV SOURCE CIRCUITS W o Q,
MISSION SOLAR ENERGY MODULE hfSE310SQ8T Zip Cade &05t (PER NEC 690.7 110.3(f3) WITH SUPPLIED MANUFACTURER'S TEMP COEFFICIENTS) 0 N
PEAK POWER IP aJc ETC] 310 �gverage High! 96-F f 36-C j
RATED VOLTAGEri Irt�p) �3,j7 tZecard LowI -S'F I -22°C 40.12 V MODULE V(iC
RATED CURRENT mp ids Exposed Conduit Yes 12 MODULES IN DC LARGEST SERIES p o m
OPEN CIRCUIT VOLTAGE (yoc) 40.12 -0 2800 MODULE TEMP COEFFICIENT (V) x o v
SHORT CIRCUIT CURRENT i1scl 9J16 Grapevine TX
NUMBER OF SOLAR CELLS EO 12 x lap.12(VOC I.11+(-23' - 25-F (sTC1) x -02s r1 OO I = 545.10 VDC {MAXIMUM SYSTEM VOLTAGE)MODULE TEMPERATURE COEFFICIENT iVOQ -0.29W a
p
PHYSICAL SIZE 65.51h x 39.33W x 1.57d & 40.116s 12 x 33.17(VMP)= 398.04 VDC (OPERATING VOLTAGE) 1�-1
BRITTAIN RESIDENCE DEAD LOAD
Module MSE310SQBT CONDUCTORYAMPACITY W
PV SOURCE CIRCUITS (DC) N U U
'Weight 40.1 lbs [� o
9.76 MODULE ISC (A). i"i Q N
Area (Module) 17.9 sq_ ft. a r/1
15.23 MINIMUM DC AMPACITY (A)
126 OF DESIGN TEMP (INCLUDES ROOF TOP ADJ. FACTOR)
Q
Quantity Lbs. t Unit Lbs. 1 Qty. 1.12 DESIGN TEMP ADJUSTMENT FACTOR 0
Module 36 40.1 1444 0.80 CONDUIT FILL FACTOR �
Power Optimizer 36 1.0 36 Q >0
Midclamp 60 0.1 3 12.20 STRING#SC fA) = 13.62 A x
Endclamp 24 0.1 1.4 1 12 (DESIGN TEMP FACTOR) x 0.8 (FILL FACTOR) CIO
L-Foot 54 0.2 12 CONDUCTOR AMPACITY
Rail 240 0.8 195
AC CIRCUITS
Tilt Leg 0 1.5 0 r
Splice bars 1 17 1 0.5 9 42 MAX INVERTER OUTPUT (Al (EACH)
Footings 54 2.2 121 52.5 MINIMUM AC AMPACITY (A) �
96 OF DESIGN TEMP
Total 'WeightIArray 1820 Lbs 1.12 DESIGN TEMP ADJUSTMENT FACTOR v �
Total Area ) Array 644 Sq.ft- 0.80 CONDUIT FILL FACTOR
Lbs. per SQFT 2.8 Lbsisq.ft.
Lbs. per Standoff 33.7 Lbs 42.0 MAX AC OUTPUT (A) (TOTAL)
= 46.88 A � U
1.12 DESIGN TEMP FACTOR) x 0.8 (FILL FACTOR) y as
CITY OF GRAPEVINE p�G,
RELEASED FOR CONSTRUCTION o
SHEET: OF: P� .. • �..•'r o
RELEASE DOES NOT AUTHORIZE ANY WORK IN *JJ
CONRICT WITH THE BUILDING CODE OR ZONING OR ... f..../ N
J ES VI CI
CITY APPROVED PLANS TO BE KEPT OIL 1
2 ,Sso .: REVISIONS:
THE JOB SITE AT ALL TIMES t�ss►ONALG`��~
MAX AVAILABLE BACKFEED FOR SES BUS SIZE:
200A BUS x 1.2 = 240A - 175A BREAKER =
65A BACKFEED AVAILABLE
MAX BACKFED CURRENT FOR OCPD:
42A x 1.25 = 52.5A TOTAL
DATE: -Ai;2 l � BY: �' 06-28-2019
TR CTUR, ONLY
BUIL ING INSPECTION DIVISION:
RELEASE DOES NOT APPLY TO CONSTRUCTION IN
EASEMENTS OR PUBLIC RIGHT-OF-WAY.
ALL CHANGES MUST BE APPROVED
DRAWN BY: ND
DATE: 06/29/2019
WIRING
CALCULATIONS
SHEET: 3
cSfrucfurai �in9in eers
vincise.com
TOPE Frtn Rego ho, No F 20604
SINGLE LINE DIAGRAM
(6x) #10 AWG
& (lx) #8 AWG GROUND
(THWN-2/PV WIRE)
(SEE NOTE #4)
(12x) MISSION SOLAR ENERGY
MSE310SQ8T
WITH (12x) P320 POWER OPTIMIERS
(FOR GROUNDING SEE NOTE #5)
(12x) MISSION SOLAR ENERGY
MSE310SQ8T
WITH (12x) P320 POWER OPTIMIERS
(FOR GROUNDING SEE NOTE #5)
I
(12x) MISSION SOLAR ENERGY
MSE3IOSQ8T
WITH (12x) P320 POWER OPTIMIERS
(FOR GROUNDING SEE NOTE #5)
MAX AVAILABLE BACKFEED FOR SES BUS SIZE:
200A BUS x 1.2 = 240A - 175A BREAKER =
65A BACKFEED AVAILABLE
MAX BACKFED CURRENT FOR OCPD:
42A x 1.25 = 52.5A TOTAL
INVERTER A
SOLAREDGE
SE10000H-US
(W/ DC
DISCONNECT
INTEGRATED INTO
INVERTER & DC
AFCI COMPLIANT
TO UL 1699B)
3/4" EMT
(3x) #6 AWG
& (Ix) #8 AWG GROUN
D(THWN-2 WIRE)
60A VISIBLE
LOCKABLE UTILITY
AC DISCONNECT
SWITCH
EATON CUTLER
HAMMER DG221 URB
240V - NON FUSED -
SERVICE ENTRANCE
RATED
INTEGRATED RGM #8 CU BARE GROUNDING ELECTRODE
(RAPID CONDUCTOR (GEC). TO RUN
SHUTDOWN) INDEPENDENTLY OF OTHER CONDUCTORS
AND TIE DIRECTLY INTO AC GROUNDING
ELECTRODE
v
EXISTING 200A
PANEL & METER
(PANEL INSIDE
AND METER ON
OUTSIDE WALL)
BI-DIRECTIONAL
SINGLE PHASE
M
UTILITY METER
NEW 175A MAIN
L BREAKER
(DERATED FROM
200A)
60A PV BREAKER
(SEE NOTE #1 FOR
[� LOCATION)
LL
GROUNDING ELECTRODE
(SEE ELECTRICAL NOTES 98)
ELECTRICAL NOTES
1. THE PHOTOVOLTAIC CONNECTION IN THE PANEL BOARD
SHALL BE POSITIONED AT THE OPPOSITE (LOAD) END FROM
THE INPUT FEEDER LOCATION OR MAIN CIRCUIT LOCATION
PER NEC ART. 705.12(D)(7) WHEN USING THE 120% OF RATING
ALLOWANCE FOR DETERMINING THE TOTAL RATING OF OVER
CURRENT DEVICE.
2. IDENTIFICATION AND GROUPING OF PHOTOVOLTAIC DC
CIRCUITS SHALL COMPLY WITH NEC 690.4(B) AND SHALL BE
SEPARATED FROM OTHER NON PV SYSTEM CONDUCTORS.
3. EXPOSED NON -CURRENT CARRYING METAL PARTS OF
PHOTOVOLTAIC RACKING, EQUIPMENT, AND CONDUCTOR
ENCLOSURES SHALL BE GROUNDED IN ACCORDANCE TO NEC
690.47 (C)(3), 250.64(C), 250.66, & 250.134 OR 250.136(A) AND
SIZED PER 250.166 REGARDLESS OF VOLTAGE.
4. ALL CONDUIT ON ROOF NEEDS TO BE PLACED 1 /2"-3 1/2" OFF
THE ROOF'S SURFACE.
5. EACH MODULE (AND MICRO -INVERTER, IF APPLICABLE)
SHALL BE GROUNDED PER THE MANUFACTURER'S
INSTRUCTIONS USING THE BONDING MIDCLAMP /
COMPONENTS, AND AT EACH ROW UTILIZING AMPHENOL
HELIO LUGS (UL 2703). SPEC SHEETS CAN BE PROVIDED UPON
REQUEST.
6. ELECTRICAL EQUIPMENT INSTALLED SHALL BE LISTED,
LABELED, OR CERTIFIED FOR ITS USE BY A NATIONALLY
RECOGNIZED TESTING LABORATORY (NRTL).
7. ALL TERMINATIONS OF EQUIPMENT TO BE A MINIMUM 75
DEGREE CELCIUS PER NEC 110.14(C) & TABLE 310.15 (13)(16) 75
DEGREE COLUMN COPPER.
8. FOR SERVICE UPGRADES, IF THE EXISTING GROUNDING
ELECTRODE SYSTEM CAN NOT BE VERIFIED, OR IS ONLY
METALLIC WATER PIPING, OR IT HAS A RESISTANCE GREATER
THAN 25 OHMS, IT IS THE CONTRACTOR'S RESPONSIBILITY TO
INSTALL A SUPPLEMENTAL GROUNDING ELECTRODE AT
LEAST 6' FROM THE EXISTING GROUNDING ELECTRODE.
9. ALL BREAKERS AND SERVICE EQUIPMENT ARE RATED AT
22kAIC OR HIGHER
10. GROUND BUSHINGS TO BE USED ON ALL METALLIC
RACEWAYS.
CITY OF GRAPEVINE
RiLEASED FOR CONSTRUCTION
SHEET: S OF:
RELEASE DOES NOT AUTHORIZE ANY WORK IN
CONFLICT WITH THE BUILDING CODE OR ZONING ORDINANCE.
CITY APPROVED PLANS TO BE KEPT ON
THE JOB SITE AT ALL TIMES
DATE: 5 94ac BY: a'
BUILDING INSPECTION DIVISION:
RELE ESE DOES NOT APPLY TO CONSTRUCTION IN
ASEMENTS OR PUBLIC RIGHT-OF-WAY.
ALL CHANGES MUST BE APPROVED
U
o
W
�
N
aIN�raN
00
O
"
0
p ,-� W
—.4
N
O
t`
w
V
G� a�
V
0 Poo
C�
*P.4
� o
� o
a
O
0
N
REVISIONS:
DRAWN BY: ND
DATE: 06/28/2019
SINGLE LINE
DIAGRAM
SHEET: 4
ARRAY DIAGRAM
---+ _ 1+• - -+ -
• • +----------
ARRAY 1
(12x) MISSION SOLAR ENERGY MSE310SQ8T
WITH (12x) P320 POWER OPTIMIZERS
(FOR GROUNDING SEE NOTE #5)
+ _
— 4- -
- + L - —
ARRAY 2
(12x) MISSION SOLAR ENERGY MSE3I OSQ8T
WITH (12x) P320 POWER OPTIMIZERS
(FOR GROUNDING SEE NOTE #5)
rr
■
•-------------�
+ =
1 +
-+ _ — -
ARRAY 3
(12x) MISSION SOLAR ENERGY MSE310SQ8T
WITH (12x) P320 POWER OPTIMIZERS
(FOR GROUNDING SEE NOTE #5)
rr
((
•
- -■
-----------
MAX AVAILABLE BACKFEED FOR SES BUS SIZE:
200A BUS x 1.2 = 240A - 175A BREAKER =
65A BACKFEED AVAILABLE
MAX BACKFED CURRENT FOR OCPD:
42A x 1.25 = 52.5A TOTAL
------------�---
- -9- v 19
---------- 4-------------•--------------
n
+
(6x) #10 AWG
& (lx) #8 AWG GROUND
(THHN-2/THWN-2/PV WIRE)
(SEE NOTE #4)
ELECTRIC AL NOTES
0
1.
THE PHOTOVOLTAIC CONNECTION IN THE PANEL BOARD
'
SHALL BE POSITIONED AT THE OPPOSITE (LOAD) END FROM
v
THE INPUT FEEDER LOCATION OR MAIN CIRCUIT LOCATION
PER NEC ART. 705.12(D)(7) WHEN USING THE 120% OF RATING
O d1
N
ALLOWANCE FOR DETERMINING THE TOTAL RATING OF OVER
OO
CURRENT DEVICE.
N
O M
2.
IDENTIFICATION AND GROUPING OF PHOTOVOLTAIC DC
CIRCUITS SHALL COMPLY WITH NEC 690.4(B) AND SHALL BE
p O
SEPARATED FROM OTHER NON PV SYSTEM CONDUCTORS.
O CCj
a
3.
EXPOSED NON -CURRENT CARRYING METAL PARTS OF
PHOTOVOLTAIC RACKING, EQUIPMENT, AND CONDUCTOR
-�
ENCLOSURES SHALL BE GROUNDED IN ACCORDANCE TO NEC
690.47 (C)(3), 250.64(C), 250.66, & 250.134 OR 250.136(A) AND
CI
SIZED PER 250.166 REGARDLESS OF VOLTAGE.
4.
ALL CONDUIT ON ROOF NEEDS TO BE PLACED 1/2"-3 1/2" OFF
THE ROOF'S SURFACE.
5.
EACH MODULE (AND MICRO -INVERTER, IF APPLICABLE)
SHALL BE GROUNDED PER THE MANUFACTURER'S
INSTRUCTIONS USING THE BONDING MIDCLAMP /
>
COMPONENTS, AND AT EACH ROW UTILIZING AMPHENOL
V
N
HELIO LUGS (UL 2703). SPEC SHEETS CAN BE PROVIDED UPON
W
U U
REQUEST.
1-I
6.
ELECTRICAL EQUIPMENT INSTALLED SHALL BE LISTED,
!04
W
LABELED, OR CERTIFIED FOR ITS USE BY A NATIONALLY
RECOGNIZED TESTING LABORATORY
�y x
(NRTL).
7.
ALL TERMINATIONS OF EQUIPMENT TO BE A MINIMUM 75
O
O W
DEGREE CELCIUS PER NEC It 0. 14(C) & TABLE 310.15 (B)(16) 75
~ ~
DEGREE COLUMN COPPER.
�y
a
�
8.
FOR SERVICE UPGRADES, IF THE EXISTING GROUNDING
ELECTRODE SYSTEM CAN NOT BE VERIFIED, OR IS ONLY
METALLIC WATER PIPING, OR IT HAS A RESISTANCE GREATER
THAN 25 OHMS, IT IS THE CONTRACTOR'S RESPONSIBILITY TO
INSTALL A SUPPLEMENTAL GROUNDING ELECTRODE AT
'--i
LEAST 6' FROM THE EXISTING GROUNDING ELECTRODE.
O
9.
ALL BREAKERS AND SERVICE EQUIPMENT ARE RATED AT
22kAIC OR HIGHER
10.
GROUND BUSHINGS TO BE USED ON ALL METALLIC
RACEWAYS.
CITY OF GRAPEVINE
RELEASED FOR CONSTRUCTION
SHEF7: OF:
RELEASE DOES NOT AUTHORIZE ANY WORK IN
OONRICT'NffH THE BUILDING CODE OR ZONING ORDINANCE.
CITY PPROVED PLANS TO BE KEPT ON
THE JOB SITE AT ALL TIMES
DATE: XI t ao BY:
BUILDING INSPECTION DIVISION:
RELEA 5E DOES NOT APPLY TO CONSTRUCTION IN
EkSEMENTS OR PUBLIC RIGHT-OF-WAY.
ALL CHANGES MUST BE APPROVED
.�
•F"
.F" 'd
cl a$
0
.F
� o
� o
a
0
0
N
REVISIONS:
DRAWN BY: ND
DATE: 06/28/2019
ARRAY
DIAGRAM
SHEET: 5
THREE LINE DIAGRAM
INVERTER
SOLAREDGE
SE10000H-US
WITH INTEGRATED DC DISCONNECT AND DC
COMBINER
AFCI COMPLIANT TO UL1699B
(INTEGRATED RGM (RAPID SHUTDOWN))
+ �� + + DC L2
+ + AC N
J
3/4" EMT
(6x) #10 AWG
& (Ix) #8 AWG GROUND
(THHN-2/THWN-2/PV WIRE)
(SEE NOTE #4)
GFPD G
a
3/4" EMT
(3x) #6 AWG
& (Ix) #8 AWG GROUND
(THHN-2/THWN-2 WIRE)
---------- G• - -
+
60A VISIBLE LOCKABLE
UTILITY AC DISCONNECT
SWITCH
EATON CUTLER HAMMER
DG22IURB 240V - NON
FUSED - SERVICE
ENTRANCE RATED
#8 CU BARE GROUNDING ELECTRODE
CONDUCTOR (GEC). TO RUN INDEPENDENTLY
OF OTHER CONDUCTORS AND TIE DIRECTLY
INTO AC GROUNDING ELECTRODE
MAX AVAILABLE BACKFEED FOR SES BUS SIZE:
200A BUS x 1.2 = 240A - 175A BREAKER =
65A BACKFEED AVAILABLE
MAX BACKFED CURRENT FOR OCPD:
42A x 1.25 = 52.5A TOTAL
ELECTRICAL NOTES
O
1. THE PHOTOVOLTAIC CONNECTION IN THE PANEL BOARD
'
SHALL BE POSITIONED AT THE OPPOSITE (LOAD) END FROM
v
THE INPUT FEEDER LOCATION OR MAIN CIRCUIT LOCATION
r T l
PER NEC ART. 705.12(D)(7) WHEN USING THE 120% OF RATING
w Q1
ALLOWANCE FOR DETERMINING THE TOTAL RATING OF OVER
ONO
CURRENT DEVICE.
N
O M
2. IDENTIFICATION AND GROUPING OF PHOTOVOLTAIC DC
v'
CIRCUITS SHALL COMPLY WITH NEC 690.4(B) AND SHALL BE
p O rA
SEPARATED FROM OTHER NON PV SYSTEM CONDUCTORS.
N
3. EXPOSED NON -CURRENT CARRYING METAL PARTS OF
� O
a
PHOTOVOLTAIC RACKING, EQUIPMENT, AND CONDUCTOR
ENCLOSURES SHALL BE GROUNDED IN ACCORDANCE TO NEC
I ��
690.47 (C)(3), 250.64(C), 250.66, & 250.134 OR 250.136(A) AND
�I
�1
SIZED PER 250.166 REGARDLESS OF VOLTAGE.
r
4. ALL CONDUIT ON ROOF NEEDS TO BE PLACED 1/2"-3 1/2" OFF
THE ROOF'S SURFACE.
5. EACH MODULE (AND MICRO -INVERTER, IF APPLICABLE)
SHALL BE GROUNDED PER THE MANUFACTURER'S
INSTRUCTIONS USING THE BONDING MIDCLAMP /
r 1 >
C)
COMPONENTS, AND AT EACH ROW UTILIZING AMPHENOL
W
EXISTING 200A
HELIO LUGS (UL 2703). SPEC SHEETS CAN BE PROVIDED UPON
U N
METER &PANEL
REQUEST
Q+ Q N
DIRECTIONAL
a
r SINGLE PHASE
6. ELECTRICAL EQUIPMENT INSTALLED SHALL BE LISTED,
Q
W
UTILITY METER
M
LABELED, OR CERTIFIED FOR ITS USE BY A NATIONALLY
RECOGNIZED TESTING LABORATORY
o 44 �
I� ul
<
(NRTL).
P-
NEW 175A MAIN
- BREAKER
7, ALL TERMINATIONS OF EQUIPMENT TO BE A MINIMUM 75
O O a
- - _ _ ,
DEGREE CELCIUS PER NEC 110.14(C) & TABLE 310.15 (B)(l6) 75
- - - - - - - �. (DEBATED FROM
DEGREE COLUMN COPPER.
�y
W
-, 200A)
a
18. FOR SERVICE UPGRADES, IF THE EXISTING GROUNDING
NEW 60A PV BREAKER
ELECTRODE SYSTEM CAN NOT BE VERIFIED, OR IS ONLY
1 - ' (SEE NOTE #1 FOR
METALLIC WATER PIPING, OR IT HAS A RESISTANCE GREATER
LOCATION)
THAN 25 OHMS, IT IS THE CONTRACTOR'S RESPONSIBILITY TO
INSTALL A SUPPLEMENTAL GROUNDING ELECTRODE AT
N _
LEAST 6' FROM THE EXISTING GROUNDING ELECTRODE.
9. ALL BREAKERS AND SERVICE EQUIPMENT ARE RATED AT
GROUNDING ELECTRODE
22kAIC OR HIGHER
(SEE NOTE 48)
V [�
10. GROUND BUSHINGS TO BE USED ON ALL METALLIC
RACEWAYS.
4
�I
CITY OF GRAPEVINE
0
FEELEASED FOR CONSTRUCTION
r
7
�, o
a
S ET: OF: �s
R SE DOES NOT AUTHORIZE ANY WORK IN
o
CONRXT WITH THE BUILDING CODE OR ZONING ORDINANCE.
N
CITY APPROVED PLANS TO BE KEPT ON
THE JOB SITE AT ALL TIMES
REVISIONS:
DATE:. 2 .2f 2-0 BY:
BUILDING INSPECTION DIVISION:
RELI EASE DOES NOT APPLY TO CONSTRUCTION IN
DRAWN BY: ND
I EASEMENTS OR PUBLIC RIGHT-OF-WAY.
DATE: 06/28/2019
ALI. CHANGES MUST BE APPROVED
THREE LINE
-
DIAGRAM
SHEET5.1
THIS LABEL TO BE INSTALLED AT DISTRIBUTION
EQUIPMENT (MAIN SERVICE PANEL, PV SOLAR
COMBINER PANELBOARD, AC DISCONNECT)
(NEC 690.53, & 690.54)
MAX RATED AC OUTPUT OPERATING CURRENT: 42 A
OPERATING AC VOLTAGE: 240VAC
THIS LABEL TO BE INSTALLED INVERTER
(PV POWER SOURCE INFORMATION (NEC 690.53, & 690.54)
THIS LABEL TO BE INSTALLED AT PHOTOVOLTAIC
INVERTER OR GROUND FAULT INDICATOR
(PER NEC 690.5(C))
WARNING
ELECTRIC SHOCK HAZARD
IF A GROUND FAULT IS INDICATED,
NORMALLY GROUNDED CONDUCTORS MAY
BE UNGROUNDED AND ENERGIZED
THIS LABEL TO BE INSTALLED AT
PV COMBINER PANELBOARD
RATED MAX POWER POINT CURRENT: 29.4 ADC WARNING
RATED MAX POWER POINT VOLTAGE: 380 VDC PHOTOVOLTAIC SOLAR ONLY.
MAX SYSTEM VOLTAGE: 480 VDC NO ADDITIONAL LOADS ALLOWED
SHORT CIRCUIT CURRENT: 15 ADC
THIS LABEL TO BE INSTALLED AT DISTRIBUTION
EQUIPMENT (MAIN SERVICE PANEL, PV SOLAR
COMBINER PANELBOARD)
WARNING
THIS EQUIPMENT FED BY MULTIPLE SOURCES.
TOTAL RATING OF ALL OVERCURRENT
DEVICES, EXCLUDING MAIN SUPPLY
OVERCURRENT DEVICE, SHALL NOT EXCEED
AMPACITY OF BUSBAR
THIS LABEL TO BE INSTALLED AT DISTRIBUTION
EQUIPMENT (MSP, PV SOLAR
COMBINER PANELBOARD) ADJACENT TO THE
INVERTER BACK -FED BREAKER
WARNING
INVERTER OUTPUT
CONNECTION
THIS LABEL TO BE INSTALLED AT THE
ENERGIZED DISCONNECTING MEANS.
(PER NEC 690.13(B), NEC 690.15, NEC
CAUTION: PHOTOVOLTAIC ELECTRIC SYSTEM CONNECTED
THIS LABEL TO BE INSTALLED AT THE
PV DISCONNECTING MEANS.
(PER NEC 690.15, IFC 605.11.1, & IFC 605.11.1.4.
PHOTOVOLTAIC
AC DISCONNECT
THIS LABEL TO BE INSTALLED WHERE ALL
TERMINALS OF THE DISCONNECTING MEANS
MAY BE ENERGIZED IN THE OPEN POSITION
(PER NEC 690.17(E))
WARNING - ELECTRIC SHOCK HAZARD
DO NOT TOUCH TERMINALS. TERMINALS ON
BOTH THE LINE AND LOAD SIDES MAY BE
ENERGIZED IN THE OPEN POSITION.
THIS LABEL TO BE INSTALLED AT EACH AND EVERY
JUNCTION BOX, COMBINER BOX, AC/DC DISCONNECT,
AND EVERY DEVICE WHERE UNGROUNDED CIRCUITS MAY
BE EXPOSED DURING SERVICE (PER NEC 690.35(F))
WARNING - ELECTRIC SHOCK HAZARD
THE CURRENT CIRCUIT CONDUCTORS OF THIS
PHOTOVOLTAIC POWER SYSTEM ARE UNGROUNDED
BUT MAY BE ENERGIZED WITH RESPECT TO GROUND
DUE TO LEAKAGE PATHS AND/OR GROUND FAULTS
THIS LABEL SHALL APPEAR AT EVERY SECTION OF THE
WIRING SYSTEM THAT IS SEPERATED BY ENCLOSURES,
WALLS, PARTITIONS, CEILINGS OR FLOORS.
SPACING BETWEEN LABELS NOT TO EXCEED 10 FEET
(NEC 690.3 1 (G)(3), IFC 605.11.1.2)
►,/:�:i.l ►[e3ii:[�yC�Pl�7N��[�lZ�]� I�:��ili:t�
THIS LABEL TO BE INSTALLED AT THE
ENERGIZED DISCONNECTING MEANS.
(PER NEC 690.15 & NEC 690.53,
IFC 605.11.1, & IFC 605.11.1.4)
MAIN PV SYSTEM
DISCONNECT
THIS LABEL TO BE AT THE
MAIN ELECTRICAL SERVICE PANEL.
(PER NEC 690.56(C)(L)A
PHOTOVOLTAIC SYSTEM
EQUIPPED WITH RAPID
SHUTDOWN
PERMANENT SIGNAGE NOTES
1. ALL LABELS / PLAQUES AND SIGNAGE IS REQUIRED
BY THE 2017 EDITION OF THE NATIONAL ELECTRICAL
CODE AS REQUIRED. PROVIDE ALL WARNING,
LABELS AND MARKINGS AS REQUIRED IN THE 2017
NEC.
2. PROVIDE ALL LABELS, CODE REFERENCES AND
SPECIFICATIONS IN COMPLIANCE WITH 2O17 NEC
ARTICLE 690 NEC SOLAR PHOTOVOLTAIC AND
ARTICLE 705 INTERCONNECTED ELECTRIC POWER
PRODUCTION SYSTEM.
3. PROVIDE WARNINGS, LABELS, MARKINGS AND THE
LOCATION WHERE THEY SHALL BE INSTALLED, AS
SPECIFIED IN ARTICLE 690 NEC, 705 FOR SOLAR
PHOTOVOLTAIC SYSTEMS.
4. EQUIPMENT SHALL BE INSTALLED IN ACCORDANCE
WITH THE 2017 NEC AND ALL APPLICABLE
REQUIREMENTS OF THE SERVING ELECTRIC UTILITY
COMPANY AND OF THE LOCAL AUTHORITY HAVING
JURISDICTION
5. LABEL BREAKER "PHOTOVOLTAIC ELECTRIC POWER
SOURCE" PER NEC 705.10 AND 'BREAKERS ARE
BACKFED" PER 690-64(B)(5). LABEL MAXIMUM A/C
OUTPUT OPERATING CURRENT AND OPERATING
VOLTAGE PER NEC 690.54
6. LABEL "PHOTOVOLTAIC SYSTEM UTILITY
DISCONNECT SWITCH", SWITCH COVER TO BE
LOCKED AT ALL TIMES, SWITCH TO BE ACCESSIBLE
PER UTILITY REQUIREMENTS AND CONFORM TO NEC
705.22
7. LABEL "PHOTOVOLTAIC POWER SYSTEM DEDICATED
KWH METER"
8. PROVIDE WARNING SIGN PER NEC 690.17 READING
"WARNING -ELECTRIC SHOCK HAZARD -DO NOT
TOUCH TERMINALS- TERMINALS ON BOTH LINE AND
LOAD SIDES MAY BE ENERGIZED IN THE OFF
POSITION.
9. LISTING AGENCY NAMES AND NUMBERS TO BE
INDICATED ON POWER INVERTER AND SOLAR
MODULES PER NEC 110.3(B)
10. METALLIC CONDUIT SHALL BE USED WITHIN
MWOw &E)
RE�,�'� $ED JCTMOMBINER
PA (IF USED , AD DO NOT AD S TO THIS PANEL
SHEE f : F:
RELE, kSE DOESFINMAUlt4DRFICATION,
OONRJCT V IITH THE "MWGSWDffopVoNWWoRDNVMEG.
'PROVED PLANS TO BE KEPT ON
THE JOB SITE AT ALL TIMES
DATE: -2/911= BY: 5;1-?•
BUIL61NG INSPECTION DIVISION:
RELEA: iE DOES NOT APPLY TO CONSTRUCTION IN
E►SEMENTS OR PUBLIC RIGHT-OF-WAY.
ALL 01HANGES MUST BE APPROVED
V
W
7
•--{ �--�
hey
w �
REVISIONS:
DRAWN BY: ND
DATE: 06/28/2019
PLACARDS
SHEET: 6
N_
00
0
'4
PHOTOVOLTAIC
SYSTEM SIE:STANDARD ECO
9 Brittain Residence
10.00 kW AC 110 E. Houston St.,
2600 Pool Road Grapevine, TX 76051 11.16 kW DC San Antonio, TX 78205
SINGLE PHASE 120V/240V TX License #:32439
solar=ee
SolarEdge Power Optimizer
Module Add -On For North America
P300 / P320 / P370 / P400 / P405
PV power optimization at the module -level
— Up to 25% more energy
- Superior efficiency (99.5%)
- Mitigates all types of module mismatch losses, from manufacturing tolerance to partial shading
— Flexible system design for maximum space utilization
- Fast installation with a single bolt
— Next generation maintenance with module -level monitoring
— Module -level voltage shutdown for installer and firefighter safety
USA dge.us
solar=@@ SolarEdge Power Optimizer
Module Add -On for North America
P300 / P320 / P370 / P400 / P405
P370
P300 P320
P400 P405
for 60-cell mad- for high -power
( (for
(for higher -power
72 & 96-cell {for thin film
ules) 60-cell modules)
60 and cell modules) modules)
— -_,—
le
modules) _ —
INPUT
Rated Input DC Powerl'!
............................
300 320
_
W
Absolute Maximum Input Voltage
..................370..................400........
........405.....
.........
(Voc at lowest temperature)
48 60 80
125
Vdc
MPPT Operating Range
8 - 48 8 - 60 8 - 80
......................................
12.5 - 105
..................
Vdc
Maximum Short Circuit Current...I.
.............................n't(Is..................-..........I..,..........
10 11 10:1
... ...........................
Adc.....
Maximum DC Input Current
..............I................1...................................
12.5 E 13:75 12:63
Adc
Maximum Efficiency
99.5
%
Wei hted Eff cienc
......g....--..I ............................
98.8
%
...
Overvoltage Category_
_ _ _ _ _ _ _ _ II
OUTPUT DURING OPERATION (POWER OPTIMIZER CONNECTED TO OPERATING SOLAREDGE INVERTER)
Maximu.m Output Current
15
A dc
.
.......
Maximum Output Voltage
...........................
.._oltage _ 60 ,
Vdc_
_85
OUTPUT DURING STANDBY (POWER OPTIMIZER DISCONNECTED FROM SOLAREDGE INVERTER OR SOLAREDGE INVERTER OFF)
_
Safety Output Voltage per Power
_Optimizer
�- -- - - - -- -- -- - 1 - -
Vdc
STANDARD COMPLIANCE
EMC
-..-.1.............................
FCC Part15 Class B, IEC61000-6-2, IEC61000-6-3
..-.-.-..-.--..
..............
Safety ...... .......
.......... ............... ....................................
............... ......... IEC62109-1 (class ll safety), UL1741
_RoHS _ _ _
Yes
-INSTALLATION SPECIFICATIONS
- — — �— —
Maximum Allowed System Voltage
1000
Vdc
Compatible inverters
All SolarEdge Single Phase and Three Phase inverters
Dimensions (W x L x H)
128x152x35/
128 x 152 x 27.5 / 5 x 5.97 x 1.08
128x152'x50/
mm / in
Sx5.97x1.37
5x5.97x1.96
Weight (including cables)
630 / 1;4 750 / 1.7
.. ....................................................................
845 / 1.9
gr / Ib
MC4 /
Input Connector
MC4 Compatible
Amphenol AH4MC4 Compatible
..... ... .................. I
.
Double Insulated;
Output Wire Type / Connector
Double Insulated; MC4 Compatible MC4 / Double Insulated; MC4 Compatible
Amphenol AH4
Output Wire Length
.........
0 95 j 3 0 1.2 / 3 9
m/ ft
Operatin�TemperatureRanpe
_.........
-40-+85/ 40-+185
"C/'F
Protection .Rating
............. ......... .
IP68 / NEMA6P
Relative Humidity
0 - 100
%
("Rated STC power of the module. Module of up to+5%power
tolerance allowed.
PV SYSTEM DESIGN USING _
SINGLE PHASE
A SOLAREDGE INVERTER(21(3)
SINGLE PHASE THREE PHASE 208V THREE PHASE 480V
HD -WAVE
Minimum String Length
(Power Optimizers)
g 10 18
Maximum String Length
(Power Optimizers)
25 25 50
5700 (6000 with
Maximum Power per String
5250 6000 12750
W
Parallel Strings of Different Lengths
or Orientations
.............................................................................................
Yes
.
4'1 For detailed string sizing information refer to: http://www.sulareclge.com/sites/default/files/string_sizing_na.pdf
''it is not allowed to mix P405 with P300/P370/P400/P600/P700 in one string
solar =@"
Single Phase Inverter
with HD -Wave Technology
for North America
SE3000H-US / SE380OH-US / SE5000H-L
SE6000H-US / SE760OH-US / SE10000H-
solar m.
"wart#'-
r� e�
WattanW
g ,
44
!
Optimized installation with HD -Wave technology
Specifically designed to work with power optimizers
Record -breaking efficiency
Fixed voltage inverter for longer strings
Integrated arc fault protection and rapid shutdown for NEC 2014 and 2017, per article 690.11 and 690.12
UL1741 SA certified, for CPUC Rule 21 grid compliance
Extremely small
— High reliability without any electrolytic capacitors �,�
— Built-in module -level monitoring
— Outdoor and indoor installation wave
— Optional: Revenue grade data, ANSI C12.20 Class 0.5 (0.5% accuracy)
www.solaredge.us
solar=@@Single Phase Inverter
with HD -Wave Technology for North America
SE3000H-US / SE380OH-US / SE5000H-US /
SE6000H-US/ SE760OH-US / SE1000OH-US / SE1140OH-US
_
SE3DOOH-US I 0H SE380-US SESOOOH-US
---
SE6000H_US
SE760OH-US ! SE10000H-US SE1140OH-US
OUTPUT
- - ---
- - -
- --- ---
Rated AC Power Output
3000
3800 @ 240V 5000
6000 @ 240V
7600 10000
11400
VA
...... ._.
,3..... . 08V
5000 �,208V,
Max. AC Power Output
3000
3800 @ 240V
5000
6000 @ 2401!
7600 10000
11400
VA
3300. 208y.................
. 5000 @, 208V,
............. .
................
AC Output Voltage Min.-Nom: Max.
�
(183-208 Z29)
_
Vac
..........................
AC Output Voltage Min.-Nom: Max.
.
Vac
(211.; 240 - 264)...........................
1................�............ .
...
AC Frequency (Nominal) ...............
59.3.:60.:60:51'..,........
Hz
Maximum Continuous Output Current
.....................
208V.....................................
16
24
A
Maximum Continuous Output Current
240V......
12.5
16 21
...............
25
............................
32 42
......
47.5
...........
A
GFDI Threshold
1
A
Utility�Nloriitoring, Islencl�ing�Proti=ction,
..................
CountEyCon K!!rableThresholds-_L____
___- —_
Yes
INPUT
Maximum DC Power @240V
...........................................................................................
1 4650 5900
7750
9300 11800 15500
17650 W
Maximum DC Power @208V
5100
....,.,,..............,.. ...............................
7750 -
........
Transformer -less, Un rounded
�....................
Maximum In ut Volta a
!?........�................
....,Yes ...................
480
Vdc
Nominal DC Input Voltage
...
380
400
Vdc
Maximum Input Current 208V
9 (
13 5
Maximum Input Current @240V......
............................
8:5...........105......1.....
.......... .....
135......
�......165......1...... ZO.. ??
Max. Input Short Circuit Current
.............
.............30:5.....
45
Adc
Reverse -Polarity Protection
.. .. ..
..................
Yes
Ground -Fault Isolation Detection
..................2..........................................
600kn Sensitivity
Maximum Inverter Efficiency
99
99.2
%
CEC Wei hted Efficiency
....................................................,.............
99
.... .,.,
30
Nighttime Power Consumption—
W
ADDITIONAL FEATURES
Supported Communication Interfaces RS485, Ethernet, ZigBee (o tional), Cellular o tional
......... ............................. P.................. I . P....... )..
Revenue Grade Data, AN51 C12,20 OptionaliZl
..........................
Rapid Shutdown - NEC 2014 and 2017
690 12 Automatic Rapid Shutdown upon AC Grid Disconnect
STANDARD COMPLIANCE
-
-
Safety
UL1741, UL1741 SA, UL16998, CSA C22:2: Canadian AFCI according to T.I. L; M .07_
Grid Connection Standards
IEEE1547, Rule 21, Rule 14 (HI)
...................14(H..................................
Emissions _ _
FCC Part_15 Class B
... .........
INSTALLATION SPECIFICATIONS
_
_
AC Output Conduit Size / AWG Range
3/4" minimum / 14-6 AWG
minimum /14-4 AWG
DC Input Conduit Size / # of Strings /
3/4" minimum / 1-2 strings / 14-6 AWG
3/4" minimum / 1-3 strings /
AWG,Rang? ...............................
AVVG............
Dimensions with Safety Switch (HxWxD)
........ ............14:6
17.7 x 14.6 x 6.8 / 450 x 370 x 174
21.3 x 14.6 x 7.3 % 540 x 370
. .
in / mm
x 185
..............................
Weight with Safety Switch
............. ................
22 / 10 25.1 / 11.4 i 26.2 / 11.9
38.8 / 17.61.
Ib k
Noise ..................................
<25
...............................................
<50
dBA
Cooling
Natural Convection
................................................
Natural convection
Operating Temperature Range
..•
13 to +140 / 25 to +60i31 (40`F % :40'C option)I"i,.
.
F / ..
Protection Rating
NEMA 3R (Inverter with Safety Switch)
Itl For other regional setngs please contact SolarEdge support
1�1 Revenue grade inverter P/N: SExxxxH-US000NK2
iat For power de -rating information refer to: https://www,solaredge.com/sites/default/files/se-temperature-derating-note-na.pdf
i4i -40 version P/N: SE—H-US000NN1.14
FM
U a:i�.11
CERTIFIED RELIABILITY
> Tested to UL1703 & IEC standards
> PID Resistant
SUPERIOR AESTHETICS
> All -black design coupled with outstanding power output
> Ideal for residential & commercial applications
13 EXTREME WEATHER RESILIENCE
> 5631 Pa snow load (117 psf) tested load to UL1703
> 185 mph wind rating*
BAA COMPLIANT FOR GOVERNMENT PROJECTS
> Buy American Act
)American Recovery & Reinvestment Act
I
AP
LINEAR WARRANTY PRODUCT WARRANTY
300-qlOW 100%
97%
Mission Solar Energy Warranty
j 90.7%
CLASS LEADING POWER OUTPUT 90% o
80.2%!
80%
I
18.6 / 70%
MAXIMUM EFFICIENCY 1 5 10 15 20 25
YEARS
_0,il + 3 940
POSITIVE POWER TOLERANCE
High -Power, American Quality
Mission Solar Energy is headquartered in San Antonio, TX with module
facilities onsite. We produce American quality poducts ensuring the
highest power output and reliability to our customers. Our product line
is well suited for residential, commercial and utility applications. Every
Mission Solar Energy product is certified and surpasses industry
standard regulations, proving excellent performance over the long-term.
www.missionsolar.com I info@missionsolar.com
CERTIFICATIONS
IEC 61215/ IEC 61730/ IEC 61701 UL 1703
-�', I:l us PQw�r�uard CEC
\_:-
LISTED
'As there are different certification requirements in different markets, please contact your local
Mission Solar Energy sales representative for the specific certificates applicable to the products in
the region in which the products are to be used.
`185 mph wind rating based upon installation at 30* or less fixed tilt mount
TM
MISSION SOLAR 0i
ENERGY ■0 11
PERC 60
SPECIFICATIONS
.ELECTRICAL
Electrical Parameters at Standard Test Conditions (STC)
Module Type
MSE300SQST
MSE305SQBT
MSE310SQ8T
Power Output
Pmax
Wp
300
305
310
Module Efficiency
%
18.05
18.35
18.65
Tolerance
0-+3%
0-+3%
0-+3%
Short -Circuit Current
Isc
A
9.571
9.664
9.760
Open Circuit Voltage
Vac
V
40.08
40.10
40.12
Rated Current
Imp
A
9.058
9.202
9.345
Rated Voltage
Vmp
V
33.12
33.14
33.17
Fuse Rating
15
20
20
Normal Operating Cell Temperature (NOCT)
46.09*C (±2°C)
Temperature Coefficient of Pmax
-0.377%/°C
Temperature Coefficient of Voc
-0.280%/*C
Temperature Coefficient of Isc
0.039%/°C
Log i.g a11►+ tl�
Maximum System Voltage 1,000VDC
Operating Temperature Range -40°C (-400F) to +85°C (185*F)
Maximum Series Fuse Rating 20A
Fire Safety Classification Class C
Front &Back Load (UL standard) 5631Pa (117 psf) Tested toUL1703 standard
Hail Safety Impact Velocity 25mm at 23 m/s
Solar Cells P-type Mono -crystalline Silicon (156.75mm)
Cell orientation 60 cells (6x10), 5 busbar
Module dimension 1664mm x 999mm x 40mm
(65.53 in. x 39.33 in. x 1.58 in.)
Weight 18.2 kg (40.1 lb)
Front Glass 3.2mm (0.126 in.) tempered,
Low -iron, Anti -reflective coating
Frame Anodized aluminum alloy
Encapsulant Ethylene vinyl acetate (EVA)
J-Box Protection class IP67 with 3 bypass -diodes
Cables PV wire, 1m (39.37 in.), 4mm2 / 12 AWG
Connector MC4
SHIPPING INFORMAT19U.
Container FT
Pallets
Panels
305 W
53'
Double stack
36
936
285.48 kW
40'
Double stack
28
728
222.04 kW
Panels
Weight
Height
Width Length
Pallet
26
1,105lbs
45.50"
45.50" 67.00"
Mission Solar Energy reserves the right to make specification changes without notice
CLASS LEADING 300-31OW
IEC
61215/61730/61701
UL
UL 1703 listed
Snus
PoWe.,Guord CEC
UmIll
MSE305SQ8T: 305WP, 60CELL SOLAR MODULE
CURRENT -VOLTAGE CURVE
12
Cells Temp.
10
a
N 6
c
0
U
a
2 -
0
Incident Irrd•=1,000 2 W/m
305.1 W
Incident Irrd.=800 2W/m
2• A W
Incident Irrd.=600 2W/m
!. 1. W
Incident Irrd.=400 zW/m 123 L
Incident Irrd.=200 'W/m 5' VY
t
0
20 30 20
Voltage [V]
Current -voltage characteristics with dependence on irradiance
and module temperature
BASIC DESIGN (UNITS: mm)
-
3�:A
z� - irlili )J 11I 1111 1
Front View
�e 50
_ I
35.00
I 'F
' --Drain
-� Hole �I 297.00
, ! I .
1-�
77.00
832.00 ' f
! Mo- unting Hole
I,
I
ii
-)---Y, Grounding
Hole
eaz oo II'
4-
I�, 1
,000 _�-
I
Back View
1
MISSION SOLAR
ENERGY sue' <
Mission Solar Energy 18303 S. New Braunfels Ave., San Antonio, Texas 78235
info@missionsolar.com I www.missionsolar.com
"A& IRONRIDGE Integrated Grounding System Installation Overview
Simplified Grounding
Fnr (',rPatPr RnfPty R I rnn/ar (r),zt
Traditionally, solar modules are grounded by attaching
lugs, bolts or clips to the module frame, then connecting
these to a copper conductor that runs throughout the
array. This process adds time and cost to the installation,
and often results in improper grounding, creating
significant long-term safety risks.
The IronRidge Integrated Grounding System solves these
challenges by bonding modules directly to the mounting
rails. This approach eliminates separate module
grounding hardware, and it creates many parallel
grounding paths throughout the array, providing
greater safety for system owners.
londing Strap
onding Straps are used to
)nd rail -to -rail connections.
hey are only required on the
til with the grounding lug.
#' Grounding Mid Clamp
Each Grounding Mid Clamp pierces through the
anodized coatings of both the module frame and
the mounting rail to form secure electrical bonds,
which are repeated throughout the array
Grounding Lug
A single Grounding Lug
connects an entire row
of PV modules to the
grounding conductor.
Install Roof Attachments
• Install appropriate roof flashing and/or standoff for roof type
• Attach L-Feet to flashing or standoff.
Prepare Rail Connections
• Insert splice into first rail, then secure with Bonding Strap and
self -drilling screw.
• Slide second rail over splice, then secure with opposite end of
Grounding Strap and self -drilling screw.
0 Mount & Ground Rails
• Attach rails to L-Feet and level rails.
• Install one Grounding Lug per row of modules.
• Connect Grounding Lug to grounding conductor
Install Modules & Clamps
• Install first module using End Clamps and Grounding Mid Clamps.
• Install additional modules using Grounding Mid Clamps.
• Finish row with a second pair of End Clamps.
Testing & Certification
The IronRidge Integrated Grounding
System has been tested and certified to
UL 2703 by Intertek Group plc.
UL 2703 is a proposed UL standard
for evaluating solar module mounting
and clamping devices. It ensures these
devices will maintain strong electrical and
mechanical connections over an extended
period of time in extreme outdoor
environments.
The testing process closely mirrors that
of UL 1703, the solar module testing
standard, including temperature and
humidity cycling, electrical and mechanical
load testing, and manufacturing quality
reviews.
Module Frame Compatibility
Dimension Range
A 31.Omm - 51.Omm
A B 5.08mm (minimum)
Any module frames whose parameters are not listed in the
provided table have not been tested for compatibility.
The Grounding Mid Clamp has proven robust in grounding solar
modules with a box frame construction, a range of anodization
thicknesses and nominal lengths of 78.5' or less.
All solar modules listed to UL 1703 and with frame construction
within the parameters stated above are compatible with the
IronRidge Integrated Grounding System.
Go to ironridge.com/ig
Jilt ngattr. rvwrr.ironrtd WCJA t-aw:227-W3 for more tnfor 1pnwai.... - /-,! � f is,
Manual
.,'.lt I RON RI DGE
Installation
Once the end module is set into position, place second
module into position, leaving a 1/2" gap between it and
the previous module. While holding module in place, drop
Grounding Mid Clamps into rail slots and rotate nuts to
engage T-bolts.
Slide second module flush against clamp tabs. Once
clamp teeth are in contact with both module frames and
the bolts are properly aligned in slots, torque to 84 in-Ibs
(55 in-Ibs for SunPower modules). Repeat procedure for
each following module.
► Make sure indent at top of T bolt is perpendicular to rail slot to
ensure T bolts are properly seated.
► If grounding mid clamps need to be reinstalled, slightly move the
modules so that clamp teeth are in contact with a new section of
the module frame.
Markings
Markings are located on the top surface of the Grounding
Mid Clamp and being with the manufacturing and model
number followed by the revision and manufacturing date.
Manufacturer and model number: IR
Revision and manufacturing date:
First digit (revision code): A = Rev A, B = Rev B, etc.
Second digit (month produced): A = Jan, B = Feb, etc.
Third & fourth digits (year produced): 15 = 2015, etc.
Ratings
Max Overcurrent Protective Device (OCPD) Rating: 25A
Installer is responsible for and shall provide an appropriate
method of direct -to -earth grounding according to the latest
edition of the National Electrical Code, including NEC 250:
Grounding and Bonding, and NEC 690: Solar Photovoltaic
Systems.
If loose components, loose fasteners or corrosion
are found during periodic inspection, replace affected
components immediately.
Grounding Mid Clamp
Leave � 1. Drop in Clamps
ap Between Parallel to Rail
Modules -
„r.
2. Rotate Nuts
to Engage Bolts
Place Second Module
into Position
in Rail Slot
Torque to 84 in-Ibs
(55 in-n-Ibsbs for
SunPower modules)
- --------_--
T-Bolt Indent
Perpendicular
to Rail
i
IR AA01
0
7OPS = ErLtx
Module Compatibility
The Grounding Mid Clamp may be used to ground and/or mount a PV module complying with UL 1703 only when the
specific module has been evaluated for grounding and/or mounting in compliance with the included instructions. Unless
otherwise noted, "xxx" refers to the module power rating and both black and silver frames are included in the certification.
AstroEnergy Solar
Modules with 35, 40, and 45mm frames and model identifier aaSM66yyPzz-xxx; where "aa" can be CH or A; "yy' can be either 10 or
"zz"
12; can be blank or (BL).
Modules with 40mm frames and model identififer CS6Y-xxxZ; where "Y" can be K, P, V, or X; and ""Z"" can be M, P, PX, or P-SD.
Modules with 35, 40, and 50mm frames and model identifier ET-Y6ZZxxxAA; where "Y" can be P, L, or M; "ZZ" can be 60 or 72; and
Canadian Solar
ET Solar
"AA" can be WB, WW, BB, WBG, WWG, WBAC, WBCO, WWCO, WWBCO or BBAC.
GigaWatt Solar
Modules with 40mm frames and model identifier GWxxxYY; where "YY" can be either PB or MB.
Modules with 40, 45, and 50mm frames and model identifier HSLaaP6-YY-1-xxxZ; where "aa" can be either 60 or 72; "YY" can be
Hanwha Solar
PA or PB; and "Z" can be blank or B.
Hanwha O CELLS
Modules with 32, 35, 40, and 42mm frames and model identifier O.YY-ZZ-xxx; where "YY" can be PLUS, PRO, or PEAK; and "ZZ"
can be G3, G4, L-G2, L-G3y, L-G4y, BFR-G3, BLK-G3, BFR-G4, BFR-G4.1, or G4.1/SC.
Hyundai
Modules with 35 and 50mm frames and model identifier HiS-YxxxZZ; where "Y" can be M or S; and "ZZ" can be MI, MF, MG, SG,
Rl, RG, TI, or TG.
Modules with 40 and 45mm frames and model identifier JAyyzz-bb-xxx/aa; where "yy' can be M6 or P6; "zz" can be blank, (K), (L),
JA Solar
(R), (V), (BK), (FA), (TG), (FA)(R), (L)(BK), (L)(TG), (R)(BK), (R)(TG), (V)(BK), (BK)(TG), or (L)(BK)(TG); "bb" can be 48, 60, or 72;
and "aa" can be MP, SI, PR, 386, 4BB, 4BB/RE.
Jinko
Modules with 35 and 40mm frames and model identifier JKMYxxxZZ; where Y' can either be blank or S; and "ZZ" can be M, P, PP,
P-B, or P-V.
Modules with 46mm frames and model identifier KYxxxZZ-AA; where "Y" can be D or U; "ZZ" can be blank, GX, or SX; and "AA"
Kyocera
can be LPU, LFU, UPU, LIPS, LPB, ,LFB, LFBS, LF132, LP62, 3AC, 313C, 3FC, 4AC, 413C, 4FC, 4UC, 5AC, 5131C, 5FC, 5UC, 6BC,
6FC, or 813C.
LG
Modules with 35, 40, and 46mm frames and model identifier LGxxxyl z-bb; where "y" can be A, N, or S; "z" can be C or K; and "bb"
can be A3, 133, G3, C4 or K4.
Mistubishi
Modules with 46mm frames and model identifier PV-MYYxxxZZ; where "YY" can be LE or JE; and "ZZ" can be either HD, HD2, or
FB.
Motech
IM and XS series modules with 40, 45, and 50mm frames.
Panasonic
Modules with 35mm frames and model identifier VBHNxxxSAyy; where "yy" can be either 06, 068, 11, 11 B, 15, 156, 16 or 1613.
Phono Solar
REC Solar
Renesola
SolarWorld
Stion
SunEdison
Suniva
Sunpower
RECOGNIZED
COMPONENT Suntech
Trina
�i�)Us
Winaico
Intertek
4008083 Yingli
Modules with 35, 40, and 45mm frames and model identifier PSxxxY-ZZ/A; where "Y" can be M or P; "ZZ" can be 20 or 24; and "A"
can beF,TorU.
Modules with 38 and 45mm frames and model identifier RECxxxYYZZ; where "YY" can be M, PE or TP; and "ZZ" can be blank,
BLK, SLV, or 72.
Modules with 35, 40 and 50mm frames and model identifier JCxxxY-ZZ; where "Y" can be F, M or S; and "ZZ" can be Ab, Ab-b, Abh,
Abh-b, Abv, Abv-b, Bb, Bb-b, Bbh, Bbh-b, Bbv, Bbv-b, Db, or Db-b.
Sunmodule Plus, Protect or XL mono or poly modules with 31, 33 or 46mm frames and model identifier SW-xxx.
Thin film modules with 35mm frames and model identifier STO-xxx.
Modules with 35, 40, and 50mm frames and model identifier SE-YxxxZABCDE; where "Y" can be B, F, H, P, R, or Z; "Z" can be 0 or
4; "A" can be B, C, D, E, H, I, J, K, L, M, or N; "B" can be B or W; "C" can be A or C; "D" can be 3, 7, 8, or 9; and "E" can be 0, 1 or
2.
Modules with 35, 38, 40, 46, and 50mm frames and model identifiers OPTxxx-AA-B-YYY-Z or MVXxxx-AA-B-YYY-Z; where "AA" is
either 60 or 72; "B" is either 4 or 5; "YYY" is either 100,101,700,1BO, or 161; and "Z" is blank or B.
SPR-A-xx series with standard (G3) or InvisiMount (G5) 46mm frames; where "A" is either E or X; and "xx" is the series number
Vd, Vem, Wdb, Woe, and Wd series modules with 35, 40, and 50mm frames.
Modules with 35, 40 and 46mm frames and model identifier TSM-xxxYYZZ; where "YY" can be PA05, PC05, PD05, PA14, P014, or
PD14; and "ZZ" can be blank or A or A.05 or A.08.
Modules with 35 and 40mm frames and model identifier Wsy-xxxz6; where "y" can be either P or T; and ""z"" can be either M or P.
Panda, YGE, and YGE-U series modules with 35, 40, and 50 mm frames.
�= 0 2015 IronFtidge, Inc- All nghls t**&v@'d. ► on wwwurwwidge.com or call 1-40W 7-9 z I- rnara fMorpn+filon. Vee�Qn t.�7
AUTHORIZATION TO MARK
This authorizes the application of the Certification Mark(s) shown below to the models described in the Product(s)
Covered section when made in accordance with the conditions set forth in the Certification Agreement and Listing
Report. This authorization also applies to multiple listee model(s) identified on the correlation page of the Listing
Report.
This document is the property of Intertek Testing Services and is not transferable. The certification mark(s) may be
applied only at the location of the Party Authorized To Apply Mark.
Applicant: IronRidge, Inc
Address:
1495 Zephyr Ave
Hayward, CA 94544
Country:
USA
Contact:
Yann Schwarz
Phone:
(800) 227-9523
FAX:
(707) 459-1833
Email:
yschwarz@ironridge.com
Party Authorized To Apply Mark: Same as Manufacturer
Report Issuing Office: Lake Forest, CA
Control Number: 4008083 Authorized by:
Manufacturer: Precision Die & Stamping, Inc
Address:
1704 W. 10th Street
Tempe, AZ 85281
Country:
USA
Contact:
Andy Frola
Phone:
(480) 967-2038
FAX:
(480) 829-0838
Email:
andy@precisiondie.com
z�l kAVI
for Thomas J. Patterson, Certification Manager
Intertek
This document supersedes all previous Authorizations to Mark for the noted Report Number
This Authorization to Mark is for the exclusive use of Intertek's Client and is provided pursuant to the Certification agreement between Intertek and its Client. Intertek's responsibility and liability are
limited to the terms and conditions of the agreement. Intertek assumes no liability to any parry, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned
by the use of this Authorization to Mark. Only the Client is authorized to permit copying or distribution of this Authorization to Mark and then only in its entirety Use of Intertek's Certification mark is
restricted to the conditions laid out in the agreement and in this Authorization to Mark. Any further use of the Intertek name for the sale or advertisement of the tested material, product or service must
first be approved in writing by Intertek. Initial Factory Assessments and Follow up Services are for the purpose of assuring appropriate usage of the Certification mark in accordance with the
agreement, they are not for the purposes of production quality control and do not relieve the Client of their obligations in this respect.
Intertek Testing Services NA Inc.
545 East Algonquin Road, Arlington Heights, IL 60005
Telephone 800-345-3851 or 847-439-5667 Fax 312-283-1672
Standard(s): UL Subject 2703 Outline of Investigation for Rack Mounting Systems and Clamping Devices for Flat -Plate
Photovoltaic Modules and Panels, Issue Number: 1, October 4, 2010
Product: XR Rails with Integrated Grounding.
Brand Name: IronRidge Roof Mount
Models: IR XR followed by 4 Alphanumeric Characters
ATM for Report 101541132LAX-002 Page 2 of 2 ATM Issued: 28-Jan-2016
ED 16.3.15 (1-Jan-13) Mandatory
IRONRIDGE
olar Is Not Always Sunny
Over their lifetime, solar panels experience countless
extreme weather events. Not just the worst storms in years,
but the worst storms in 40 years. High winds capable of
ripping panels from a roof, and snowfalls weighing
enough to buckle a panel frame. J11i
XR Rails are the structural backbone preventing
these results. They resist uplift, protect
against buckling and safely and efficiently
transfer loads into the building structure.
Their superior spanning capability
requires fewer roof attachments,
reducing the number of roof
penetrations and the amount
of installation time.
Force -Stabilizing Curve
Sloped roofs generate both vertical and lateral
forces on mounting rails which can cause them
to bend and twist. The curved shape of XR Rails
is specially designed to increase strength in both
directions while resisting the twisting. This unique
feature ensures greater security during extreme
weather and a longer system lifetime.
to
XR Rail Family
Compatible with Flat & Pitched Roofs Corrosion -Resistant Materials
XR Rails are IronRidge offers All XR Rails are made of marine -grade
A compatible with 52Va range of tilt leg aluminum alloy, then protected with an
FlashFoot and options for flat anodized finish. Anodizing prevents surface
other pitched roof roof mounting and structural corrosion, while also providing sh-10-
attachments. applications. a more attractive appearance.
CLASSIFICATION
Constructional Data Report (CDR)
11.0 Reference and Address
Report Number 101541132LAX-002 Original 22-May-2014 Revised: 15-Jan-2016
Standard(s) UL Subject 2703 Outline of Investigation for Rack Mounting Systems and Clamping Devices
for Flat -Plate Photovoltaic Modules and Panels, Issue Number: 1, October 4, 2010
Applicant IronRidge, Inc
Address
1495 Zephyr Ave
Hayward, CA 94544
Country
USA
Contact
Yann Schwarz
Phone
(800) 227-9523
(510)225-0973
FAX
(707) 459-1833
Email
vschwarzedi iron rid ile.com
Manufacturer 2 Precision Die & Stamping, Inc.
1704 W. 10th Street
Address
Tempe, AZ 85281
Country
USA
Contact
Andy Frola
Phone
(480) 967-2038
FAX
(480) 829-0838
Email
andW,:'( recisiondie.com
Manufacturer 1 IronRidge, Inc.
Address
1495 Zephyr Ave
Hayward, CA 94544
Country
USA
Contact
Jim Norsworthy Or
Dave Taggart
Phone
(707) 363-3025
(800) 227-9523
FAX
(510) 225-0975
Email
inorsworthv( ironridce.com
dtaaaart&..ironridae.com
Page 1 of 86
This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. intertek's responsibility aril
liability are limited to the terms and conditions of the agreement. Intertek assures no liability to any party, otter than to the Client in accordance with the
agreement. for any loss, expense or damage occasioned by the use of this report. Only the Client is aulhofized to permit copying or distribution of this report and
then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be
approved in writing by Intertek_ The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the
material, product, or service is or has ever been under an Intertek certification program.
Report No. 101541132LAX-002 Page 2 of 86 Issued: 22-May-2014
IronRidge, Inc. Revised: 15-Jan-2016
2.0 Product Description
Product XR Rails with Integrated Grounding.
Brand name IronRidge Roof Mount
The product covered by this report is the IronRidge Rails with Integrated Grounding solar roof
mounting system. This system is designed to provide bonding and grounding to photovoltaic
modules. The mounting system employs anodized aluminum rails that are roof mounted using
aluminum Extruded L Foot brackets. The mounting rails in this report are XRL, XR10, XR100
and XR1000 Rail. All rails have an optional aluminum splice which ties the rails together to
extend their length.
A grounding strap and stainless steel hardware are required for penetrating the anodized
coating of the rails, creating a bonded connection from rail to rail. 304 stainless steel Grounding
Mid Clamp and aluminum End Clamps are used to attach and support framed photovoltaic
modules to the system. The End Clamps are not used as a grounding means.
The Grounding Mid Clamps are installed onto the module frame by using a 18-8 stainless steel
serrated T-Bolt and a 18-8 stainless steel Flange Hex Nut that gets screwed onto the rails to a
Description specified torque. The retention teeth of the clamp and bolt penetrate the anodized coating of
the photovoltaic modules frame and rail to contact the metal, creating a bonded connection
from module to module and module to rail.
The grounding of the entire system is intended to be in accordance with the latest edition of the
National Electrical Code, including NEC 250: Grounding and Bonding, and NEC 690: Solar
Photovoltaic Systems. Any local electrical codes must be adhered in addition to the
national electrical codes. An entire array, regardless of size, is grounded via one grounding
lug. The WEEB Grounding Lug is secured to XRL, XR10, XR100 or XR1000 Rail's top slot
using stainless steel hex bolt or T-Bolt, flat washer, split lock washer, and nut, tightened to
manufacture's specified torque. The WEEB Grounding Lug is intended for use with one solid or
stranded copper wire, conductor size 14 AWG though 6 AWG. The Titan Grounding Lug is
secured to XRL, XR10, XR100 or XR1000 Rail's side center cavity of rails using stainless steel
T-bolt, k-lock nut, star washer, and machine screw. The Titan Grounding Lug is intended for
use with one solid or stranded copper wire, conductor size 14 AWG though 4 AWG.
Models IR XR followed by 4 Alphanumeric Characters
Model Similarity N/A
Fuse Rating: 20 A
Fire Class Resistance Rating:
- Class A for Steep Slope Flush -Mount (Symmetrical) Applications when using Type 1,
Type 2 and Type 3, Listed Photovoltaic Module.
Ratings - Class A for Low Slope Flush -Mount (Symmetrical) Applications when using Type 1,
Type 2 and Type 3, Listed Photovoltaic Module.
- Class A for Steep Slope Tilt -Mount ( Asymmetrical) Applications when using Type 1
and Type 2, Listed Photovoltaic Module.
- Class A for Low Slope Tilt -Mount ( Asymmetrical) Applications when using Type 1,
Type 2 and Type 3, Listed Photovoltaic Module.
ED 16.3 15 (1-Jan-13) Mandatory
Report No. 101541132LAX-002
IronRidge, Inc.
2.0 Product Descri
Page 3 of 86
Issued: 22-May-2014
Revised: 15-Jan-2016
These systems were evaluated or tested for bonding ana grounamg wain the toliowing PV-
Module frames:
Motech - Black or Silver Frames
Models:
IM and XS series, 60 and 72 cell modules with 40 mm frame height.
IM and XS series, 60 and 72 cell modules with 45 mm frame height.
IM and XS series, 60 and 72 cell modules with 50 mm frame height.
Suntech - Black or Silver Frames
Models:
Wdb, Wde, and Wd series, 60 and 72 cell modules with 35 mm frame height.
Vd series, 60 and 72 cell modules with 50 mm frame height.
ET Solar - Black or Silver Frames
Models:
ET Solar 60 cell modules with 35 and 40 mm frames
ET-Y660xxxZZ
Where "Y" can be P, L, or M; "xxx" refers to the module power rating; "ZZ" can be WB, WW,
BB, WBAC, or BBAC
ET Solar 72 cell modules with 40 and 50 mm frames
ET-Y672xxxZZ
Where "Y" can be P, L, or M; "xxx" refers to the module power rating; "ZZ" can be WB, WW,
BB, or WBG
Hyundai - Black or Silver Frames
Models:
SG, MG, RG and TG Series, 60 cell modules with 35 mm frame height.
MI, RI and TI Series, 72 cell modules with 50 mm frame height.
Yingli - Black or Silver Frames
Models:
Panda and YGE models, 60 cell modules with 40 mm or 35 mm frame height.
YGE models, 72 cell modules with 50 mm or 40 mm frame height.
Kyocera -
Models:
KD(xxx)GX-LPU, KD(xxx)GX-LFU, KD135SX-UPU, KD(xxx)GX-LFBS, KD(xxx)GX-LPB
KD(xxx)GX-LFB, KD(xxx)GX-LFB2, KD(xxx)GX-LPB2
KD135GX-LPS, KD140GX-LPS, KD140SX-UPU
KU(xxx)-3AC, KU(xxx)-4AC, KU(xxx)-5AC, KU(xxx)-3BC, KU(xxx)-4BC
KU(xxx)-5BC, KU(xxx)-6BC, KU(xxx)-8BC, KU(xxx)-3FC, KU(xxx)-4FC
KU(xxx)-5FC, KU(xxx)-6FC, KU(xxx)-4UC, KU(xxx)-5UC.
Where xxx refers to the module power rating
Canadian Solar - Black or Silver Frames
Models:
CS6P-M 60 Cell Modules with a 40mm frame height.
CS6P-P 60 Cell Modules with a 40mm frame height.
CS6X-M 72 cell modules with a 40mm frame height.
CS6X-P 72 cell modules with a 40mm frame height.
Report No. 101541132LAX-002
IronRidge, Inc.
2.0 Product
Other Ratings
Page 4 of 86
Issued: 22-May-2014
Revised: 15-Jan-2016
LG Modules - Black or Silver Frames
Models:
LG 60 cell modules with 35 mm frames:
LGxxxy1z-b3
Where xxx is the module power rating, "y" can be A,N or S, 'Y' can be C or K, and "b" can be
A, B, or G.
LG 60 cell Modules with 40mm frames:
LGxxxy1 z-G4
Where "xxx" is the module power rating, "y' can be N or S, and 'Y' can be C or K
LG 72 Cell Modules with 46mm frames:
LGxxxy2z-b3
Where "xxx" is the module power rating, "y" can be N or S, 'Y' can be C or K, and "b" can be A,
B, or G
Suniva Modules - Black or Silver Frames
Models:
60 Cell Modules with 35 and 40mm frames:
O PTxxx-60-A-YYY-Z
M VXxxx-60-A-YYY-Z
Where "xxx" is the module power rating, "A" is either 4 or 5, "YYY" is either 100,101,700,1 B0,
or 1131, and 'Y' is blank or B.
72 Cell Modules with 38, 46, and 50mm frames:
OPTxxx-72-A-YYY-Z
MVXxxx-72-A-YYY-Z
Where "xxx" is the module power rating, "A" is either 4 or 5, "YYY' is either 100,101,700,1 BO,
or 1131, and "Z" is either blank or B
Hanwha Modules - Black or Silver Frames
Models:
HSL72P6-PA-1-xxx(50mm frame)
HSL72P6-PB-1-xxx(45mm frame)
HSL60P6-PB-1-xxx(40mm frame)
HSL60P6-PA-1-xxx(45mm frame)
The model number can be followed with a "B"
Where xxx is the module power rating
Trina Solar Modules - Black or Silver Frames
Models:
TSM-xxxPA05 (35mm frame height)
TSM-xxxPC05 (35mm frame height)
TSM-xxx-PD05 (35mm frame height)
TSM-xxxPA05 (40mm frame height)
TSM-xxxPA14 (46mm frame height)
TSM-xxxPD14 (40mm frame height)
TSM-xxxPC14 (40mm frame height)
The model number can be followed by A and .05 or .08
Where xxx refers to module power rating
ED 16.3.15 (I-Jan-13) Mandatory
ED 16.3.15 (1-Jan-13) Mandatory
Report No. 101541132LAX-002 Page 5 of 86 Issued: 22-May-2014 Report No. 101541132LAX-002 Page 6 of 86 Issued: 22-May-2014
IronRidge, Inc. Revised: 15-Jan-2016 IronRidge, Inc. Revised: 15-Jan-2016
2.0 Product Description 2.0 Product Description
SolarWorld Modules - Black or Silver Frames
Models:
Sunmodule Plus SW-xxx,
Sunmodule Protect SW-xxx,
Sunmodule XL SW-xxx
Mono or Poly with 31, 33, or 46 mm frame height.
Where xxx refers to the module power rating
Phono Solar Modules - Black or Silver Frames
Models:
PSxxxP-20/U, PSxxxM-20/U, PSxxxP-24/T, PSxxxM-24/T with 40mm frame height
Where xxx refers to module power rating
SunEdison modules - Black or Silver Frames
Models:
SE-QxxxBCC-3Y, SE-MxxxBCC-3Y, SE-FxxxBCC-3Y, SE-PxxxBCC-3Y, SE-QxxxBMC-3Y
SE-MxxxBMC-3Y, SE-FxxxBMC-3Y, SE-DxxxBMC-3Y, SE-PxxxBMC-3Y with 50mm frame
height.
Where xxx refers to module power rating
Hanwha Q CELLS modules - Black or Silver Frames
Models:
Hanwha QCells 60 cell modules with 32 mm frames
Q. PL U S-G4-xxx
Q.PRO BFR-G4-xxx
where xxx refers to module power rating
Hanwha QCells 60 cell modules with 35 mm frames:
Q.PRO-G3-xxx
Q. PRO-BFR-G3-xxx
Q.PEAK BLK G3-xxx
Q.PLUS G3-xxx
where xxx refers to module power rating
Hanwha QCells 72 cell modules with 35 mm frames:
Q.PRO L-G4y-xxx
Q.PLUS L-G4y-xxx
where "y" can be blank, 1 or 2 and "xxx" refers to module power rating
Hanwha QCell 72 cell modules with 40 mm frames:
Q.PRO L-G2xxx
Q.PRO L-G3y-xxx
where "y" can be blank or 1 and "xxx" refers to module power rating
Hanwha QCell 72 cell modules with 42 mm frames:
Q.PRO L-G2-xxx
where "xxx" refers to module power rating
Renesola Modules - Black or Silver Frames
Models: Mono and Virtus II Modules:
JCxxxM-24/Abh, JCxxxS-24/Abh, JCxxxF-24/Abh, JCxxxM-24/Abh-b, JCxxxS-24/Abh-b
JCxxxF-24/Abh-b, JCxxxM-24/Ab, JCxxxM-24/Abv, JCxxxS-24/Ab, JCxxxF-24/Ab
JCxxxM-24/Ab-b, JCxxxM-24/Abv-b, JCxxxS-24/Ab-b, JCxxxF-24/Ab-b with 50mm frame
height.
JCxxxM-24/Bb, JCxxxM-24/Bbv, JCxxxS-24/Bb, JCxxxF-24/Bb, JCxxxM-24/Bb-b
JCxxxM-24/Bbv-b, JCxxxS-24/Bb-b, JCxxxF-24/Bb-b, JCxxxM-24/Bbh, JCxxxS-24/Bbh
JCxxxF-24/Bbh, JCxxxM-24/Bbh-b, JCxxxS-24/Bbh-b, JCxxxF-24/Bbh-b with 40mm frame
height.
JCxxxS-24/Db, JCxxxF-24/Db, JCxxxS-24/Db-b, JCxxxF-24/Db-b with 35mm frame height.
Where xxx refers to the module power rating.
Sunpower Modules- Black or Silver Frames
Models:
SPR-E-xx series with standard (G3) or InvisiMount (G5) 46 mm frame
SPR-X-xx series with standard (G3) or InvisiMount (G5) 46 mm frame.
where xx is the series number
Panasonic Modules - Black or Sliver Frames
Models:
VBHNxxxSA06, VBHNxxxSA06B, VBHNxxxSA11, VBHNxxxSA11 B with 35 mm frame height.
Where xxx refers to the module power rating
Winaico Modules - Black or Silver Frames
Models:
Winaico 60 Cell modules with 35 and 40 mm frames
W sy-xxxz6
Where "y" can be either P or T, "xxx" is the module power rating, and 'Y' can be either M or P
Mitsubishi Modules - Black or Silver Frames
Models:
PV-MYYxxxzz
Where YY can be LE or JE, xxx is the module power rating, and ZZ can be either HD, HD2, or
FB
Jinko Solar Modules - Silver Frames
Models:
JKMxxxP-60: Where xxx is the module power rating between 250-270 in increments of 5.
JKMSxxxP: Where xxx is the module power rating between 255-270 in increments of 5.
JKMxxxPP-60: Where xxx is the module power rating between 255-270 in increments of 5.
ED 16.3,15 (1-Jan-13) Mandatory
ED 16.3.15 (1-Jan-13) Mandatory
8431 Murphy Drive
Middleton, WI 53562 USA
Telephone: 608.836.4400
Facsimile: 608.831.9279tek www.inter-com
Test Verification of Conformity
sm_
Starling Madison Lafquist, Inc,
r
r.
5224 South 3r Street, Phoenix, Anixona 85040
tel: (602) 438-2500 fox: (602) 438-2505 ROC#E291316 www.smleng.cam
IronRidge February 15, 2019
In the basis of the tests undertaken, the sample(s) of the below product have been found to comply with the requirements of
28357 Industrial Boulevard Page 1 of 21
the referenced specifications at the
time the tests were carried out.
Hayward, CA 94545
iApplicant Name & Address:
IronRidge, Inc. 1,
Attu: Mr, Carey Geiger, Vice President New Markets
1495 Zephyr Ave.
Hayward, CA 94544
Subject: IronRidge XRt(lili Rail, Roof Flush Mounting System — Structural Analysis
USA
Product Description:
XR Rails with Integrated Grounding.
Dear Sir:
Ratings & Principle
Fire Class Resistance Rating:
We have analyzed the IronRidge XRHHI Rail for the subject solar module support system and
Characteristics:
-Flush Mount (Symmetrical). Class A Fire Rated for Low Slope applications when using Type 1, 2
determined (bat, for the configurations and criteria dcseribed below, it is in compliance with the
and 3, listed photovoltaic modules. Class A Fire Rated for Steep Slope applications with Type1,
applicable sections of the following Reference Documents_
2 and 3, listed photovoltaic modules. Tested with a 5" gap (distance between the bottom the
module frame and the roof covering), per the standard this system can be installed at any gap
allowed by the manufacturers installation instructions. No perimeter guarding is required.
Codes: ASCUSEI 7-10 Min. Design Loads for Buildings &Other Structures
International F3ttild.illtg Code 2012 Edition
Models:
51-61GD-005, 51-61GD-005B, 51-5000-001 and 51-65-001
Other: AC428, Acceptance Criteria for Modular Framing Systems Used to Support PV
Brand Name:
IronRidge Roof Mount
Modules, dated Effective November 1, 2012 by ]CC -ES
Relevant Standards:
UL 2703 (Section 15.2 and 15.3) Standard for Safety Mounting Systems, Mounting Devices,
Aluminum Design I%IanuaL 2010 Edition
Clamping/Retention Devices, and Ground Lugs for Use with Flat -Plate Photovoltaic Modules
and Panels, First Edition dated Jan. 28, 2015 Referencing UL1703 Third Edition dated Nov. 18,
The IronRidge XRl00 Rail is an extruded aluminum section with an overall depth of 2.438 in, and a
2014, (Section 31.2) Standard for Safety for Flat -Plate Photovoltaic Modules and Panels.
net area of il.583 sq.in. The rails are used to support solar modules, typically, on the roof of a
Verification Issuing Office:
Intertek Testing Services NA, Inc.
building. See Exhibit 0011— attached_ The modules are clamped to the rails by the IronRidge
8431 Murphy Drive
Module 'Mounting Clamps, as shown in the attached Exhibit, The rails are attached to aluminum
Middleton, WI 53562
angle brackets that are either attached directly to the roof framing or attached to a stand that is
Date of Tests:
08/27/2014 to 03/17/2015
screwed to the roof framing- The rails are mounded across the slope with a small clearance (flush
Test Report Number(s):
101769343MID-OOlr1, 101769343MID-001a,101915978MID-001 & 101999492MID-001arl-crl.
mounting) to the tuiderlying roof Structure. The installed solar modules are at the Same Slope as the
This verification is part of the full test report(s) and should be read in conjunction with them. This report does not automatically
underlying roof structure.
imply product certification.
Completed by: Chad Naggs
Reviewed by: GregoryAllen
All loads are transferred to the roof framing through the angle brackets by simple bi-axial flexure of
Title: Technician II, Fire Resistance Title: Engineering Team Lead, Fire Resistance
the rails. The maximum span of the rails is governed by either the mid -span flexural strmes or the
deflection requirement that the rail not come into contact with the roof.
Signature:
Signature:]
Date: 03/30/2015
Date: 03/30/2015
The effect of seismic loads (for all design categories A-F) have been determined to be less than the
efTect due to wind leads in all load conditions and combinations, Therefore, the maximum allowable
spans for common load cases are shown in the tables below. Tables 1 A-9A are for modules with a
'cables
maximum lung distension of 67.5 inches and I B-9B are for modules with a maximum tang
— _
-
dimension of 78.5 inches.
This Verification is for the exclusive use of lntertek's client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are
limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client m accordance with the agreement, for any loss, expense
or damage occasioned by the use of this Verification. Only the Client is authorized to permit copying or distribution of this Verification. Any use of the Intertek name or one of its Starling Nladison Lofquist, Inc. Consulting Structural and Forensic Engineers
marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test/inspection results Texas Firm Registration #F-16420
referenced in this Verification are relevant only to the sample tested/inspected. This Verification by itself does not imply that the material, product, or service is or has ever been
under on Intertek certification program.
GFT-OP-13a (24-MAR-2014)
' r
IronRidge
Mr, Carey Geiger
IronRidge YR100 Rail, Roof 1=htsh Mounting System — Stnlctural Analysis
Modulo Glass fCe'lls
Frorne Coirnpsiitiiity,
X - I.2. 2.2 myrt
'f=15.40mm
i' -x
February 15, 200
Page 21 of 21
Figure 8: CAN-10 [`.lamp Module Frame f)imcnsional Requirements
Our analysis assumes that the rail;, including the connections and associated hardware., am installed
in a workmanlike manner in accordance v6th the IrorlRidge Flush Mount Trt.Stallation Manual" by
lronRldge and gcncrally accepted standarrls of construction practice. Additional information is
a vailable It the IronRidge web site:, IronRidge,conl. 4ferjlication of PV Module capacity to support
the loads associated with the given array shall be lihe responsibility of the Contractor of Owner and
not lronitiJgc or Starling Madison Lofquist.
The adequacy of the supporting, roof framing is to be determined by others.
Please feel line to Contact tile at your convenience if you have any questions,,
Respectfully yours,
Tres Warner, P,tr, • '•.*�
Design Division Manager h.................
TREE J. WARNER
Digitally signicd tsyTrt;3
I Warner
Trey DN: c-US omStarling
Madison Lofqulst Inc,
0
u=A014z73w00153
B F918), Cn rrn -Tres JNarner Date. 2w 9.02.- 9
1429:07-47'O6'
Starling Madison Lofquisy Inc, Cc►r,sulting SuUCLUtal and Forensic Engitrcers
Texas Firm Registrsttion 4117-16420
AUTHORIZATION TO MARK
This authorizes the application of the Certification Mark(s) shown below to the models described in the Product(s)
Covered section when made in accordance with the conditions set forth in the Certification Agreement and Listing
Report. This authorization also applies to multiple listee model(s) identified on the correlation page of the Listing
Report.
This document is the property of Intertek Testing Services and is not transferable. The certification mark(s) may be
applied only at the location of the Party Authorized To Apply Mark.
Applicant: IronRidge, Inc
1495 Zephyr Ave
Address:
Hayward, CA 94544
Country:
USA
Contact:
Yann Schwarz
Phone:
(800)227-9523
FAX:
(707) 459-1833
Email:
yschwarz@ironridge.com
Party Authorized To Apply Mark: Same as Manufacturer
Report Issuing Office: Lake Forest, CA
Control Number: 4008377
Authorized by:
Manufacturer: IronRidge, Inc
Address:
1495 Zephyr Ave
Hayward, CA 94544
Country:
USA
Contact:
Jim Norsworthy Or
Phone:
(707)363-3025
FAX:
(510)225-0975
Email:
jorsworthy@ironridge.com
IT
for Thomas J. Patterson, Certification Manager
Intertek
This document supersedes all previous Authorizations to Mark for the noted Report Number
This Authorization to Mark is for the exclusive use of Intertek's Client and Is provided pursuant to the Certification agreement between Intertek and its Client. Intertek's responsibility and liability are
limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement. for any loss, expense or damage occasioned
by the use of this Authorization to Mark. Only the Client is authorized to permit copying or distribution of this Authorization to Mark and then only in its entirety. Use of Intertek's Certification mark is
restricted to the conditions laid out in the agreement and in this Authorization to Mark. Any further use of the Intertek name for the sale or advertisement of the tested material, product or service must
first be approved in writing by Intertek. Initial Factory Assessments and Fallow up Services are for the purpose of assuring appropriate usage of the Certification mark in accordance with the
agreement, they are not for the purposes of production quality control and do not relieve the Client of their obligations in this respect.
Intertek Testing Services NA Inc.
545 East Algonquin Road, Arlington Heights, IL 60005
Telephone 800-345-3851 or 847-439-5667 Fax 312-283-1672
Standard(s): UL Subject 2703 Outline of Investigation for Rack Mounting Systems and Clamping Devices for Flat -Plate
Photovoltaic Modules and Panels, Issue Number: 1, October 4, 2010
Product: XR Rails with Integrated Grounding.
Brand Name: IronRidge Roof Mount
Models: IR XR followed by 4 Alphanumeric Characters
ATM for Report 101541132LAX-002 Page 1 of 2
ATM Issued: 28-Jan-2016
ED 16.3.15 (1-Jan-13) Mandatory
June 20, 2014
Mr. Meir Adest
SolarEdge Technologies Ltd
6 Ha'Harash St.
HOD HASHARON, ISRAEL
3933 US Route 11
Cortland, NY 13045
Telephone: (607) 753-6711
Facsimile: (607) 756-9891
www.intertek.com
Letter Report No. 101703554CRT-001
Project No. G 10 1703554
Ph: +972.9.957.6620
email: meir.a@solaredge.com
Subject: ETL Evaluation of SolarEdge Products to NEC Rapid Shutdown Requirements
Dear Mr. Meir Adest,
This letter represents the testing results of the below listed products to the requirements contained in the following
standards:
National Electric Code, 2014, Section 690.12 requirement for rapid shutdown.
This investigation was authorized by signed Quote 500534459 dated 06/10/2014. Rapid shutdown test were
perform at SolarEdge Technologies Ltd, 6 Ha'Harash St HOD HASHARON, ISRAEL and witness by Intertek
personal on 06/17/2014.
The evaluation covers installations consisting of optimizers and inverters with part numbers listed below.
The testing done has verified that controlled conductors are limited to not more than 30 volts and 240 volt-
amperes within 10 seconds of rapid shutdown initiation.
Applicable products:
0 Power optimizers:
o PBxxx-yyy-zzzz; where xxx is any number, 0-9, up to a maximum value where xxx = 350; yyy
could be AOB or TFI; and zzzz is any combination of four letters and numbers.
o OP-XXX-LV, OP-XXX-MV, OP-XXX-IV, OP-XXX-EV; where xxx is any number, 0-9.
o Paaa, Pbbb, Pccc, Pddd, Peee; where aaa, bbb, ccc, ddd, eee is any number, 0-9 to a maximum
upto aaa=300, bbb=350 ccc=500, ddd=600, eee=700.
o Pxxx, Pyyy, Pzzz, Pmmm, Pnnn and P000; where xxx, yyy, zzz is any number, 0-9 to a maximum
up to xxx=300, yyy=350, zzz=500; where mmm, nnn, 000 is any number, 0-9 to a maximum up to
mmm=405, nnn=300, 000=350
• 1-ph Inverters:
o SE3000A-US / SE380OA-US / SE5000A-US / SE6000A-US / SE760OA-US / SE1000OA-US /
SE1140OA-US when the SolarEdge rapid shutdown cable labeled "MCI-CB-xxxxx-x" which is part
of kit SE1000-RSD-xx is installed in the inverter Safety Switch where xxxxx-xx is any number;
inverter part number may be followed by a suffix
Pagel of 2
This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms
and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use
of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or
advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only the sample tested. This
report by itself does not imply that the material, product or service is or has ever been under an Intertek certification program.
FJ f Wi
Appiwed
Intertek Intertek intertek Irztei tek Intertek Intertek
Intertek Testing Services NA, Inc.
SD 12.12 (11/11110) Informative
SolarEdge Technologies Ltd
• 3-ph Inverters:
Letter Report 101703554CRT-001
June 201h, 2014
o SE9KUS / SEIOKUS / SE20KUS when the SolarEdge rapid shutdown cable labeled "MCI-CB-xxxxx-
x" which is part of kit SE1000-RSD-xx is installed in the inverter Safety Switch where xxxxx-xx is
any number; inverter part number may be followed by a suffix
This letter report completes this portion of the evaluation covered by Intertek Project No.G101703554.
If there are any questions regarding the results contained in this report, or any of the other services offered by
Intertek, please do not hesitate to contact the undersigned.
Please note, this Letter Report does not represent authorization for the use of any Intertek certification marks.
Completed by:
Radhe Patel
Reviewed by:
Howard Liu
Title:
Signature:
Engineering Team Lead
-�----- 7^
Title:
Signature
StaffEngineer
Date
June 20m, 2014
Date:
June 20` , 2014
Intertek Testing Services NA, Inc.
Page 2 of 2
So 12.1.2 (11/11/10) Informative